Jump to content
SAU Community

Help somethink wrong

SCR34M3R

By SCR34M3R,
in Engines & Forced Induction

 Share

Recommended Posts

SCR34M3R Rising Star

SCR34M3R

Posted
Posted

well i got car tuned on monday and it was going really well they said my o2 sensor was stuffed, woke up next day and over 10psi it just doesnt pull. but it just screems, so i replaced the o2 sensor thinking it was that but still same thing. its a R33 GTS-T with power fc

Cheers

Link to comment
https://www.sau.com.au/forums/topic/81139-help-somethink-wrong/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

The O2 sensor is useless when you are at full throttle, so the tuner was having an enormous lend of you. O2 sensors really only work on cruise.

As for the lack of performance > 10psi, was the PFC tuned for that boost level?

PHATGTR Collaborator

PHATGTR

Posted
Posted
well it just revs as it normally would, or sounds

Does it still run 10psi up top or does boost drop off all together?

If it is only reaching 10psi and staying there all the way to redline then it could be any number of things but I would suggest you have a wastegate actuator problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Ball bearing turbos

      By GTSBoy · Posted

      The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • sunsetR33
      Ball bearing turbos

      By sunsetR33 · Posted

      Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • GTSBoy
      R33 GTST Axles

      By GTSBoy · Posted

      There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • jdniss
      Forced Performance Hta Turbos

      By jdniss · Posted

      Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • thozza
      Intro/R33 owner

      By thozza · Posted

      Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...