Jump to content
SAU Community

Recommended Posts

Hey,

Some people have asked the schedule for this weekends Dutton Rally so that they can come down and watch (it's free to watch)

Friday 9:00am-12:00pm - DECA Shepparton

Friday 1:00pm - 4:00pm - Shepparton Airport

Saturday 9:00am - 4:00pm - Winton

Saturday 4:30pm - 6:30pm - SPC Carpark - Shepparton

Sunday 10:00am - 12:00pm - Essondon Airport Carpark

Sunday 1:00pm - 3:00pm - Police Training Centre - Atwood.

Basically that is the schedule for cars 48-96. On days one and 3 the schedule is swapped for cars 1-47. (As is cars 1-47 will do Shepparton Airport first then DECA)

But Myself and Scotsman (66), Blaise and Dan (67) and Frank and Aaron (68) are all in the 2nd group so will follow the exact schedule above.

As far as the events in Melbourne on the Sunday goes the stuff at Essondon is definitely the best to watch. Lots of great cars - 8 GTR's in total - plus a full range of Porkas (Twin turbo's, GT3's, GT2's and even a special Gemaballa Twin Turbo), as well as EVO's, STi's, BMW's etc etc.

:thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/81931-dutton-rally-schedule/
Share on other sites

Denham - it's where we did the Skidpan day with Kev.

It's ok - but watching cars go around in a circle is only so much fun. There is a little track there we have to do also thats brilliant fun to drive on but there's bugger all spots to watch it from so you don't get to see a whole lot.

Essendon is heaps better.

If anyone feels like driving up to Shepparton to spectate/drink (not to mention support the drivers and club) over the weekend we are staying at the Victoria Lake Tourist Park (check the Event Section fior more details).

Hope to see some of you around on the weekend.

:D

its pretty easy to get to.

for u just jump on ring road go around to tullamarine take that towards the city, then there is a turn off

as you come past westfield shopping centre etc, westfield will be on ur right and the airport and turnoff will be on the left.

as u come off the turnoff take the LHS sliplane and go straight.

then i have nfi where it is but im sure u can find it easy enough by the noise of the cars etc.

hope that helps

FRIDAY UPDATE

Rain interferred with play at DECA - with Snowcakes reporting 20s time differences between group 1 (dry) and his group (wet). The rain didn't hamper performance for group 1 at the airport - so they weren't disadvantaged at all.

The good news is the car isn't broken, and it's time to SARK PISS!

Apparently :rofl:

Winton tomorrow...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...