Jump to content
SAU Community

Recommended Posts

I have used the meguiars wet look polish and their wax, and while its great when its done, it requires FAR more elbow grease than the equivalent AUTOGLYM products.

Now im using AUTOGLYM super resin polish, followed by their super hard coat protectant/gloss. Its awesome stuff and HELL EASY to apply and buff off.

Save your time and effort and try this stuff.

(i use the meguiars foam applicator pads, and their terry cloth buffing towels, they are cool. Dont use an old t-shirt or tea towel!)

Originally posted by inark

how i dry my car...

140 down around the factory areas near my car wash until it is damn near dry....

The best way to do it.... The water streaming across the windshield adds to the star-trek'n boost feel of it all :thumbsup: I live near the airport so it works well for me too.

When I get back home though I've got to wipe the dirt from the back of the skirts at either side (with a dry cloth).:mad:

46n2

  • 4 weeks later...

Well an update on the washing and drying of my car.

I used the Meguiars Gold Class Wash with one of their wash mitts - great, those mitts are heaps better than sponges and the wash seemed to work well.

Then I polished most of the car using Meguiars Deep Crystal polish - recommended - it deepened the colour (red) that was really noticable. It also brought up the colour of the mirrors that are fading. Good stuff.

Then I applied Deep Crystal wax over the top of the polish (after rubbing off the polish of course). This was all based on Meguiars web site on how to do it properly. They recommend to polish first then wax.

I found the Meguiars products much easier to wipe off than say Turtle Wax that's for sure with much better results. I just gotta keep doing it.

Oh and one thing is for sure, in relation to towels and polishing cloths, good quality ones make life a lot easier and you get better results. I had some cheaper polishing cloths that didn't last too long, so used those to get most of the polish/wax off then a Meguiars towel to finish it off.

I too polished my car 2-3wks ago with Meguiars Deep Cystal Polish and it was damn easy with damn good results. All up it took me around an hour and the paint (red) came up like the car was brand new its amazing. Washing is so much easier now with heaps better results.

I also got a new chamois which cost me about $19, 1 wipe of any section now matter how much water is on it and its totally dry, no streaks or water stains etc just perfect.

if u read the back of some of the meguiars stuff it says to have the water streaming across the car......i.e dont use a nozzle. I gave this a try and I found that if I use the nozzle i get lots of beads all over the car...and it takes ages to chamois it dry. But if you stream it over your car the water just rolls off...and you dont have to chamois off very much water.

give it a try people.

I tried with the water streaming after reading the back of the Meguiars stuff and it works, much less water. Dragging the chamois also works too - still can't get used to something wet actually drying !!!!

I also used the Meguiars (yes I have nearly even product of theirs now) foam applicator pads - what a great way to apply polish/wax, so easy and you tend to use less as the foam absorbs some of it so you don't need to keep putting new stuff on all the time.

Meguiars = revelation for Red Sky :lol:

BTW has anyone used Meguiars Deep Crystal paint cleaner or Scratch X? - I want to fix up the roof that looks ugly with lots of marks and rough paint even after washing, polishing and waxing.

Buy the biggest and best synthetic chamios you can buy, that does make a difference. Mine was $40. Its huge and works well.

Another tip if you want your windows to look really clean and clear :

1. Spray windows with Windex.

2. Wipe off with 2 sheets of black n white newspaper per window.

Do the inside of the windows too.

It leaves no streaks at all. Give it a try. You wont be dissapointed.

Cheers

i just used meguiars scratch X and OMG some of my scratches have virtually dissapeard, and I swear by Gold Class liquid wax and shampoo (yes I buy the christmas packs :P)

I think the trick to getting the chamois ready is to always wash it in soapy warm water after every wipe, then run it thru warm water, wring then wipe again... well its what I do, and it works best for me. For soap I just use a bit of Maguiars shampoo (left over from car wash)

Alright guys don't laugh at me.

Tiny bit off topic.

Is is alright to wash the inside of the muffler as i do this at the moment with my 3 inch tips and like the clean look instead of all that sooty crap, also has a nicer note afterwards, but i'm getting a skyline with HKS super drager and want to know if its a no-no due to rust and stuff

Originally posted by Jimbo2000

Alright guys don't laugh at me.

Tiny bit off topic.

Is is alright to wash the inside of the muffler as i do this at the moment with my 3 inch tips and like the clean look instead of all that sooty crap, also has a nicer note afterwards, but i'm getting a skyline with  HKS super drager and want to know if its a no-no due to rust and stuff

You actually notice the difference from cleaning the little bit of soot out of your exhaust tip? You must have a keen eye for detail.

Washing a Super Dragger won't hurt because its made out of stainless-steal. IE: Won't rust. Just don't squirt water inside it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...