Jump to content
SAU Community

How to replace front parking light?

Sydneykid
 Share

Recommended Posts

Terminal Grand Master

Terminal

Posted
Posted

It's a friction clip, just pops out. I had the same trouble, but i also had to remove my eyelids to get it off. same as the rear lights, they feel like they're going to break off, but it's just a really tight clip

emanuelt Rising Star

emanuelt

Posted
Posted

Once it is loose you should be able to get a screw driver in the gap behind the parker light, use a torch as well and try and leaver it off a bit, getting as close to the clip as you can, after a lot off pulling and leavering it should just pop off, feels like its going to break, and then you'll say OH it was just that little dam clip. :hellpisd:

  • 1 month later...
Sydneykid Grand Master

Sydneykid

Posted
  • Author
Posted (edited)
do the headlights need to come out, too get the parker globes?

Nope, just undo the philips head screw that holds the parker assembly onto the top of the headlight assembly. Then pull the parker assembly straight forward by slipping a couple of fingers behind it. It is very tight, just make sure you pull it straight, not up or down or outwards.

:wub: cheers :wub:

Edited by Sydneykid
  • 5 months later...
GoldZilla Grand Master

GoldZilla

Posted
Posted
Nope, just undo the philips head screw that holds the parker assembly onto the top of the headlight assembly. Then pull the parker assembly straight forward by slipping a couple of fingers behind it. It is very tight, just make sure you pull it straight, not up or down or outwards.

:laugh: cheers :laugh:

My parkers are blue in colour and when I was at a petrol station earlier this week, a cop mentioned that I should change them. I think it's better to be safe than sorry rather than risk a defect.

Tried to get my parkers off last night, and again tonight after having read this thread. I tried pulling them out with a bit of force after undoing the Phillips head screws, but thought I'd better check with those who've already done it before I break them.

Do I pull them forward towards (but away from, if that makes sense?) the front of the car, and can anyone please post a pic of where the clip is and where I should put a screwdriver to lever it off (without scratching the paint)? Is the clip behind or below the parker?

Thanks in advance...

Nick

muck Community Regular

muck

Posted
Posted

from memory.. i was pulling forwards away from the car...

and i had the screwdriver pushing with my other arm from under the front bar.... i think i had to jiggy the washer bottle.. this was the left side...

the left was a bitch.. the right popped out without fuss...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DatsunBanana
      Rear subframe stay bracket bolt removal issues

      By DatsunBanana · Posted

      I didn't know about induction heaters but checked them out and they look awesome but too pricey for the occasional job like this. And I'm too nervous to take a flame anywhere near there as the petrol tank is so close, although I was intrigued with the crayons suggestion 😁 I filled a coke bottle lid with penetrating fluid and raised it on the jack so the nut was submerged in it all night. Then went in with a tiny cold chisel and got it almost to the point of splitting but not quite (I didn't want to damage the bolt threads). Then I hammered a socket back on and gently worked it until I felt movement. And it's off 😀
    • GTSBoy
      RB25DET Series 1 & Series 2 Gearbox Identification

      By GTSBoy · Posted

      I should. But it already uses too much fuel for a daily. You might note my recco for engine chnages are almost exclusively to people who have it as a weekender/summer car. I don't even have room to keep the spares for this one, let alone another car.
    • MBS206
      RB25DET Series 1 & Series 2 Gearbox Identification

      By MBS206 · Posted

      He should do an LS7 too...
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      If I had "perfect R33 GTR" kinda money I would have bought one of the crazy expensive low mileage HJA cars, but I am sadly not that wealthy. I already picked this car out of various Skylines for sale locally, most of which were worse in some way. Only a few cars were actually better but also more expensive. In terms of buying a motor locally, I at least have the option to inspect it myself and juding the seller as a person, and used or freshly rebuilt engines that some people sell are actually ok price-wise. I knew the car was going to require work, but shit piled up real fast and I haven't even driven 1000km yet as the turbo started oiling like a bitch within a few weeks after I got the car.   I assume it wasn't actually me who cracked it, though there is no way to know when that crack formed and if the previous owner even knew it was there. Buying another 05U Block can be a gamble, yeah, but the cheapest PRP cast block is like twice or more money-wise, and billet is 3 or 3 times as much. For now I am most likely just keeping the current engine, as a rebuild or engine swap isn't happening right now. But I am seriously considering buying a second engine and selling mine in return. Might be a sweet deal at the end.
    • sunsetR33
      RB26 turbo oil banjo bolts

      By sunsetR33 · Posted

      Hi all. I need some help buying the correct size banjo bolts for my 2860 turbos. Because whoever installed them tore up the original part, I ordered new ones of this kind, because I just figured these were the most leak-resistant option as I already had trouble with a shitty braided line. I need to know the thread size of the smaller left hole, that is the turbo oil feed connection. I found out so far that the turbo oil inlet apparently has a 7/16"-24 thread, but I cannot find any listing or description of the thread size on this line. I do not have the original bolts. I tried using the bolts that were in the turbos (the ones that were mounted with the shitty braided line) but they sit very loosely so they can't be the right thread. Means either these bolts are the wrong ones (how do they fit the turbo then? no clue) or the wraparound-lines have a different thread than the turbo oil feed itself. Help is appreciated, asking Nissan directly is obviously not going to work.
×
×
  • Create New...