Jump to content
SAU Community

Recommended Posts

It turns out I didn't blow the turbo, I blew off an intercooler pipe. But I couldn't see it on the night cause it was under the car and dark. But the turbo is definetly on the way out cause theres oil in the intercooler pipes. I'll drive like an old woman for a month or so and replace it with something a bit bigger. :D

Link to comment
https://www.sau.com.au/forums/topic/8271-hicks-is-happysort-of/
Share on other sites

Originally posted by KILLER-T

I think a bit of oil in thr cooler pipes is normal if you are running a bit of extra boost just buy a oil catch can :D

im not too sure, I've had the pipes off quite a bit, when i painted them and polished the intercooler. also had the inlet pipe off when I changed the plugs(c#nt of a job) but theres never been oil in there before.

Originally posted by Hicks

I'll drive like an old woman

So what is new Hicks??:bahaha:

Good to see that your car is just barely alive, but I agree with Killer-T that it is probably not that much too worry about, but if you need an excuse to drive slowly then its OK with me.

See'ya:burnout:

Originally posted by Hicks

It turns out I didn't blow the turbo, I blew off an intercooler pipe. But I couldn't see it on the night cause it was under the car and dark. But the turbo is definetly on the way out cause theres oil in the intercooler pipes. I'll drive like an old woman for a month or so and replace it with something a bit bigger. :D

It's scary when you blow a pipe off, does make you think the worst. I blew a vacume hose at the plex last time and I thought it was a dead turbo too. I had a look under the bonnet and found the hose, went out and kept dragging :D

Seriously sounds like blow by, this can be increased by increasing boost, or even using a oil thats a bit too thin when you change it. Would investigate a catch can as coating your coola isn't a good way of improving efficiency:D

Good luck getting it sorted - only if to get GTS-t VSPEC off your case....hehehehe.

Steve

Originally posted by GTS-t VSPEC

I never had oil in my pipes till I ran higher boost.

I run standard boost and have a bit of oil.

Catch-can you say ?

BTW: My next oil change is due shortly, what does everyone use/recommend ? and how much is it ? (also, how many Ls to fill up?)

-Kym.

Hes ripping u off m8.

U change ure oil every 5000ks right? whats the point of puttin redline in (unless ure a sheik or something) just use good ol Mobil1 synth half the price and will be dam close to as good as redline for that time period.

Its not just the oil in the pipes that worried me, its the way that smoke slowly rises from the exaust when I back it off after reving it.

BTW paul, your a tool. I might head down to the plex to watch you get some more 14 second passes. :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...