Jump to content
SAU Community

Recommended Posts

Is it just me, or does everyone's paint on the wiper blades (both the front and the back, but much more predominantly on the back) faded away?? :confused:

I've only had my '93 R33 for almost a month now, but ever since I've had it the wiper blades' black paint has bloody almost all come off...

Does anyone know if it's just a simple home-job respray to fix it, or if something more complicated (and expensive... :D ) is required for a good finish?

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/8283-wiper-blades-paint/
Share on other sites

I don't paint stuff anymore, powder coating is the go. I had mine done in mat black and they look great. Only cost about $20 and if you get other stuff done at the same time it is ususlly cheaper like radiator and battery mounts and cam covers etc. Its way cheaper than good paint and lasts longer as well.

Link to comment
https://www.sau.com.au/forums/topic/8283-wiper-blades-paint/#findComment-120310
Share on other sites

Originally posted by dlskip

Where about's can you get powder coating done?

Can you do it yourself?

Lads Lads Lads....Look in your Yellow pages under "Powder Coating Services" this will open a whole new world for you :( Panel shops don't do it as it is a big enough business as it is....you know all those pool fences and stuff? Thats powder coating. Its really much cheaper than paint. Just remember that there will always be a small area that is marked from where they use wire to hold it up during the process. Also powder coating is only for metal. There are some new iridescent colours available and some shops also do a alloy flake spray that can be polished to look just like alloy.

Just pull all the metal bits off your car, take to shop tell them what colours and a couple of days later they are ready. They sand blast all the parts before coating so don't worry if they are covered in oil and dirt.

Link to comment
https://www.sau.com.au/forums/topic/8283-wiper-blades-paint/#findComment-120334
Share on other sites

For Perth people

I made enquiry

Belmont Powdercoaters

97 Abernethy Rd Belmont WA 6104

Ph: (08) 9277 3800 Powder Coating Service

this place does it

$35 + GTS minimum

but he said if we get like 10 we could do it all for $70 cuz it needs to be sand blasted etc... take pait off 1st

anyway anyone interest in it? more people is better price of course

cehers

Joe

Link to comment
https://www.sau.com.au/forums/topic/8283-wiper-blades-paint/#findComment-120653
Share on other sites

OK.....NEVER powder coat you fmic / radiator. And for that matter you really shouldn't paint them either. Painting is mainly done for asthetic reasons and not for any beneficial reason. Powder coating adds a thick layer to the object and would block off all the runners in the fmic or radiator. Basically its a tuff alternative for decorativley painted objects that require a longer lasting finish.

Link to comment
https://www.sau.com.au/forums/topic/8283-wiper-blades-paint/#findComment-121001
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...