Jump to content
SAU Community

Recommended Posts

Virtually brand new TO4e Turbo-charger. This item has travelled around 1000kms and is in excellent condition. The majority of the turbo is spotless with just a minor amount of carbon present in the exhaust housing. This particular turbo was fitted to an internally standard RB25DET and produced 298rwkw on 18 psi of boost. Be quick and grab yourself a bargain folks.

ID plate on comp cover-type HKS, T3V band, part no. TO4E and serial number is AO7100152.

One the comp cover there is J84A cast onto it and 4 10 6 stamped into it above the ID plate.

On the rear of comp housing you have 4 numbers: 5327-5794, 5617, K27.015 and HJ.

The exhaust housing measures 60 mm on the outlet side, inlet ports times 2(split pulse) are 45mm by 29mm each.

On the outside of the casting the scroll is 75mm where it leaves the T3 flange and about 40 mm where it meets the wheel trim

For Sale due to upgrade

$950

WILL ACCEPT COD IF REQUIRED

Link to comment
https://www.sau.com.au/forums/topic/84170-t04e-turbo/
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...