Jump to content
SAU Community

plex 15th


Recommended Posts

  • Replies 261
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by GTS-t VSPEC

Although Osc@r had problems with spiking I don't think this will be as bad on a stock turbo, I used one for a while and it seemed to do OK, but compared to an EBC they suck.

I found it was all to do with the setup rather than the bleeder - I used to get spiking from 15 or 16 down to 10, changed dump pipe, turbo and some other minor pieces and now it spikes about 1psi

just a std run of the mill turbodumb gated boost controller, but keeps the boost up so thats what counts

ebc I'd be most happy with but $$$ (even though a mate was telling me last nite he's getting an avc-r locally for $400, the %$&*)

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136575
Share on other sites

Don't know about the ticket thing yet.

I got to have dinner with the stones brothers team, Russel Ingal and the Ambrose boy on our table. I think Russel was impressed at the level of yahoo pissheads on our table chanting 'Russel! ...Russel!' Got to see his new BA falcon car, sit in it, try to look in the engine bay, spilt beer on it, tried to cut the cable ties that restrained the pedals and got the guys to sign my name tag so I can forge their signatures later and get into the pits if the chanting doesn't work.

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136623
Share on other sites

Originally posted by rev210

Macka: dude most stores DON'T have it, I should know I've looked in just about all of them.

Makit Hardware in Balcatta next to marlows balcatta. bout $24 for the 4L tin. Compares nicely with the cost of VP 103 for smaller volumes and craps on it for octane and energy value, it's just not as 'green'.

It's well worth a try I have a litre in the fuel at the moment (20% mix) and it gives a good old kick. 

I'm sure you will like the extra timing Macka.

Thanks Rev..

will look into it.

I just wanna be able to run standard timing with no rattle :D

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136641
Share on other sites

Macka,

I still think that VP103 is much better for the price. It is 107RON and 99MON, which is far higher than Toluene.

Toluene is good, but it is not designed as a race fuel, yes it has been used in race cars, but it is not a race fuel. If your after serious performance edge from fuel then go the VP 103.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136649
Share on other sites

Toluene is 122 RON / MON 106.

RACE FUEL not RICE Fuel.

Toluene was used during the 'turbo era' of formula 1. Back when they were running 5bars(73psi) of boost in qualiying and 4bars(59psi) in race. The fuels were limited to 102 RON so 84% toluene and 16%n-heptane (has no octane rating to bring it back to 102). Making 1500HP out of little tiny engines.... ooooright!

102 octane and 73psi? the funny thing is the octane rating of toluene is only half the reason its a bloody good race fuel.

VP103 just a compromise fuel.

Formula one racing teams know it, now you do too.

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136681
Share on other sites

rev210,

As you well know it did not ever get 122RON in a knock-engine when used in the right mix. Are you suggesting that Macka use straight toluene, I didn't think so.

I know that it can be used in race cars, but there engines are designed to cope with it, ours are not.

VP103 is a better unleaded Race Fuel, because our cars will die on straight Toluene. In the correct mix, toluene will provide a RON of 100, which will give you a bit of extra bang, but not nearly as much as the VP.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136712
Share on other sites

Let me assure you that the 'correct mix' of toluene can be higher than the suggested 100 RON without detriment.I'd suggest anything upto 40% or so can be tried.The higher mix will have low rpm and cold start issues but in small volumes for the race day will work out well if you tune the car for it. The horse power generated by the toluene is higher besides, it's a very high engery fuel.

For interest I have run a 30/35% mix , with no adjustments and no problems.

VP103 is not bad compared to the old AVgas, it makes a bit more power and is unleaded.

We can agree to disagree on which fuel to use. I will just keep handing you your ass with my much less modified car (hee hee..ho ..ho..)

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136736
Share on other sites

rev120,

I'll be interested to see what times you get running the Toluene. 40% is too much for me, but if your happy to run it then no probs.

We always disagree on this issue, but that's OK.

I think the 100RON was with a 25% mix, so your right, with more Toluene you will get a higher RON, but I've never heard anyone recommend higher then 30%.

Don't get upset if you less modified car burst into flames while doing a run on 40% Toluene.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136745
Share on other sites

You wish!

Toluene is much less volitile than VP103, the formula 1 cars had the fuel tanks heated by the exhaust to get the stuff to burn propperly. If anything running too much toluene will prevent your car from starting and your engine won't be able to combust it, ie: unburnt fuel the opposite of ping.

I disagree because I've used them both. I pick toluene for cheapness and better power.

VP103?

Go kiss it in a tree!

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136763
Share on other sites

I'd suggest that before anyone else tries 40% toluene that they ask there tuners, can't imagine many of them would recommend this approach.

I was only joking about the car blowing up, I wouldn't want to see you in flames, only the ones we trade in the posts.

So you running next week with 40% toluene? I'll be there expecting big things.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136776
Share on other sites

Ask tuner's who have used toluene you mean. There are plenty of them that talk out of thier asses, even the good ones. Make sure the tuners don't sell VP103 or Elf either otherwise you might find them a little bias.

Then again you can try a litre or two from Makit hardware at 10% or so and see what you reckon

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-136801
Share on other sites

yeah you want the % to be a little higher.

If you are a scaredy cat then start with 10%, I don't think that will make anything 'feel' different but, it will allow a snick more timing. After you have tried 10% then get 25% or 30% in there and you should 'feel' something, you can advance the timing a bit (obviously not too much cause it will ping). I advance mine till I just start to get a ping then back it off a little.

Link to comment
https://www.sau.com.au/forums/topic/8519-plex-15th/page/11/#findComment-137296
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...