Jump to content
SAU Community

Recommended Posts

G'day all.

I found this on my hard drive today. Can't remember where I got it from, but I'm sure it'll come in handy for someone.

Not sure if it's complete, but it's the full parts listing for a R33 GTR and some GTS-t parts.

Nuts, bolts, brackets, wire harnesses, panels, you name it, it's got it.

Even shows you how the parts are assembled which is cool.

The zipped gif files are 1.67 meg in total.

I couldn't find any copyright on the pics anywhere, so posting it up should be OK ????

The link to the file is here:

http://home.iprimus.com.au/jayson77/r33_pa.../Parts_List.zip

J

Link to comment
https://www.sau.com.au/forums/topic/8544-r33-parts-listings/
Share on other sites

Guy's and Shelly,,,thats part of Nissan's Parts Catalogueing,,,,. Jay I wish you had the rest of it,,,,,or where you found it... Thats just the Pics,,,,the parts numbers would be the other half,,,,.I could interpret everybodies genuine parts if we had all of it....

Neil.:D :D :)

Link to comment
https://www.sau.com.au/forums/topic/8544-r33-parts-listings/#findComment-130586
Share on other sites

Originally posted by ndr

Guy's and Shelly,,,thats part of Nissan's Parts Catalogueing,,,,. Jay I wish you had the rest of it,,,,,or where you found it... Thats just the Pics,,,,the parts numbers would be the other half,,,,.I could interpret everybodies genuine parts if we had all of it....

Neil.:):P :P

G'day Neil,

I stumbled across it ages ago on a web site and just started saving all the pics :P I've had a good hard look around for that site again but I think it's vanished :D

I'll do another good search around and see what I can find.

J

Link to comment
https://www.sau.com.au/forums/topic/8544-r33-parts-listings/#findComment-131136
Share on other sites

  • 6 months later...

No worries :D

Yepp, I've used it a few times while working on the car. Great for seeing how things come apart etc.

Last time was when I pulled the starter apart. Using this I knew there wasn't any nasty little clips and springs that were going to fling out and never to be found again :(

J

Link to comment
https://www.sau.com.au/forums/topic/8544-r33-parts-listings/#findComment-456773
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...