Jump to content
SAU Community

Recommended Posts

Hi,

I have taken the standard headunit out of my gtr to find a mess of wires behind (from a previous stereo). My problem is that when i test each of the wires for a battery wire I don't find anything with the digi meter.

Going by standard Nissan Wiring it should be black w/ red stripes but these provide nothing (I found 2 ??).

I checked all the fuses under the steering column individually and they are all fine.

Any ideas at all?

TIA Jon

Link to comment
https://www.sau.com.au/forums/topic/85476-help-with-head-unit-install-query/
Share on other sites

blk/red is the antenna trigger. are the factory plugs still on it?

you should have 4 twisted pairs of wires. these are front and rear. the gtr has that annoying amp in the rear shelf that should have been bypassed already.

red/blu is lights , should be a blue/? one that is +12v key and the other one should be a red..

( haven't worked on a skyline for a few weeks so I can't remember the colours.)

if the plugs are still on it buy an adapting plug and use that. makes life easier.

Thanks for the quick replies.

The factory unit was working when I removed it

The original plugs are all gone.

I will try and investigate further now.

After testing every wire I cannot find a +12v battery, what other things could I try?

worst case senario you could always just run a new wire from your battery..

.. have you been able to measure 12v on the ignition and lighting leads? might sound silly, but are you sure you have a good ground for your multimeter?..

cheers,

damo

You sure your using your multimeter correctly? You'd wanna have it on the 20v setting, then be testing each wire with your red probe, whilst always having your black probe grounded (could use your earth wire for the HU if u know which one it is, or the cigarette lighter, or even the headunit chassis is usually earthed also).

Best of luck,

Nasha

there is 12V memory there. you have a blown fuse. do a physical check ( remove and inspect.) every fuse. you shouldn't have an interior light currently. the fuse you are after should be outside.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I see you've never had to push start your own car... You could save some weight right now...
    • Sounds good.  I don't 100% understand what your getting at here. When you say, "I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down" do you mean this - there is a panel with factory paint, without any prep work, they paint the entire panel with primer, then colour then clear?  If that's what you mean, sure it will "stick" for a year, 2 years, maybe 3 years? Who knows. But at some stage it will flake off and when it does it's going to come off in huge chunks and look horrific.  Of course read your technical data sheet for your paint, but generally speaking, you can apply primer to a scuffed/prepped clear coat. Generally speaking, I wouldn't do this. I would scuff/prep the clear and then lay colour then clear. Adding the primer to these steps just adds cost and time. It will stick to the clear coat provided it has been appropriately scuffed/prepped first.  When you say, "but the new paint is landing on the old clearcoat" I am imagining someone not masking up the car and just letting overspray go wherever it wants. Surely this isn't what you mean?  So I'll assume the following scenario - there is a small scratch. The person manages to somehow fill the scratch and now has a perfectly flat surface. They then spray colour and clear over this small masked off section of the car. Is this what you mean? If this is the case, yes the new paint will eventually flake off in X number of years time.  The easy solution is to scuff/prep all of the paint that hasn't been masked off in the repair area then lay the paint.  So you want to prep the surface, lay primer, then lay filler, then lay primer, then colour, then clear?  Life seems so much simpler if you prep, fill, primer, colour then clear.  There are very few reasons to go to bare metal. Chasing rust is a good example of why you'd go to bare metal.  A simple dent, there is no way in hell I'm going to bare metal for that repair. I've got enough on my plate without creating extra work for myself lol. 
    • Hi, Got the membership renewal email but haven't acted yet.  I need to change my address first. So if somebody can email me so I can change it that would be good.    
    • Bit of a similar question, apprently with epoxy primer you can just sand the panel to 240 grit then apply it and put body filler on top. So does that basically mean you almost never have to go to bare metal for simple dents?
×
×
  • Create New...