Jump to content
SAU Community

Tuning Of R33

BookyVL

By BookyVL,
in Queensland

 Share

Recommended Posts

bazr33 Mentor

bazr33

Posted
Posted

im gettin my power fc installed at F.I.S.T at Wacol

they did a good job of tuning my car previously

cause my boost and timing was all outta whack .

I have been to apc with my intercooler avcr and dump pipe install

and had my intercooler piping resting against my radiater hose

and few nuts and bolts were missing .

so werent really impressed with them especially forking out 2500 for it!

got exotic exhaust to fix up the shit with the piping, did a great job.

So at the moment only going to fist, exotic exhaust to fit stuff

THanks

Link to comment
https://www.sau.com.au/forums/topic/86971-tuning-of-r33/#findComment-1571850
Share on other sites
Mr-Toy33 Grand Master

Mr-Toy33

Posted
Posted

Alot of people have highly recommended Hardcore down at Slacks Creek to me over the past week or 2 since I've been meeting a few other skyline drivers from here.

I'm taking mine down this weekend to have them check out my turbo for me as it looks like it's up for a rebuild.

Link to comment
https://www.sau.com.au/forums/topic/86971-tuning-of-r33/#findComment-1573189
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • GTSBoy
      Another "where do these lines and plugs go" RB25DET question

      By GTSBoy · Posted

      4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • GTSBoy
      R34 GTR Seats / No longer reclining

      By GTSBoy · Posted

      Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...