Jump to content
SAU Community

Brand New Greddy 600x280 Cooler And Piping

locograe
 Share

Recommended Posts

locograe Contributor

locograe

Posted
Posted (edited)

Item: 600x280x76 Greddy Bar and Plate intercooler. BRAND NEW! with brand new greddy piping, hoses and clamps

Location: Gold Coast

Item Condition: BRAND NEW

Reason for Selling: Selling car :D

Price and Payment Conditions: $600 ono

Extra Info: Don't post unless you're interested please

Contact Details: Get Grae on 0422933560 or e-mail [email protected]

post-14895-1126565763.jpg

post-14895-1126565815.jpg

Edited by locograe
locograe Contributor

locograe

Posted
  • Author
Posted (edited)

Mate the cooler will fit a GTR only if it's a single turbo conversion other wise you'll have to fabricate the pipe between the turbo's and the intake side of the cooler. eg 2 into 1

The core itself will fit no probs. It's a 600x280x76 core

Cheers

Grae

What model car is it for?  Suit a 32 GTR?  What type of Greddy cooler is it?

Edited by locograe
locograe Contributor

locograe

Posted
  • Author
Posted

I'll post some tuesday when i get to work. Best offer is $600. Full kit brand new in box. I'm in Mermaid Waters

Cheers

pretty interested, mind posting pics up? and wats ur best offer and where are u located?

Beer Baron Grand Master

Beer Baron

Posted
Posted

if you can post up some pics showing that it's genuine i probably will take it providing you can COD it to me in sydney for $600.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...