Jump to content
SAU Community

Recommended Posts

Item: 16x9.5 Inch Enkei Racing Rims

Location: Melbourne

Item Condition: 3 rims are in very good condition, one is badly damaged. Tyres aren't that good.

Price and Payment Conditions: $300 bux ono or will swap of rims to fit a ca180. Will post interstate, on full upfront payment and only if buyer pays freight.

Extra Info: These rims are off an R32.

Contact Details: PM Me, Email Me on: [email protected] or call me on 0404723623.

PICS

All of them:

enkeisall.jpg

Enkei Logo:

enkeilogo.jpg

Another logo:

enkeilogo2.jpg

Width 9.5inch:

innermeasurement.jpg

The damaged rim:

enkeidamaged.jpg

Thanks,

Ali

Edited by IOWNU
Link to comment
https://www.sau.com.au/forums/topic/88158-fs-16-inch-enkei-racing-rims-300ono/
Share on other sites

  • 4 weeks later...

Took these rims off the market, but have decided to put them up for sale again.

Alternatively will swap for a set of 4 rims to fit a ca 180.

Edited by IOWNU
What is the offset on the rims? are they off a GTR or GTS? the offset is usually stamped inside the rim +20,+30,+32 etc

They are off my cousins R32 GTST.

So they'd fit a GTST nicely.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...