Jump to content
SAU Community

Recommended Posts

Ohh btw , might have to ask a favour and do a wheel swap for a coupla weeks.

Take your pic , the 17's on the racer or the 18's on the ricer.

Need for compliance but has to go to Sydney.

Reason Niz is there is only 1 place left in Aust that has a spare R32 GTR plate and that's Sydney Compliance.

Cheers

Ken

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

joe i was bought up religous too til i was about 10 - um worse than christian - pretty embarrassed about it actually but i was brought up a J.W. but neither my parents or i have anything to do withthe religon anymore - although my grandparents try and bible bash me so its simple i just dont visit them anymore.

Originally posted by Nizmo

im fussy with my men too ken - i wouldnt still be single if i wasnt :) the rabbits were just good friends but they were good quality too rabbits without fleas :D

Bwahahaha

Funniest post I have seen so far tonight.

:)

Cheers

Ken

Originally posted by Micko

You asking me about the wheels Ken?

I'll go back & check out the pics - but the one you just posted looks great (once the stickers are gone of course).

Ken - how many r's you had now?

Note the link , GTR6

Plus the Targa one which as we know , alas , is no more.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...