Jump to content
SAU Community

Whoretown WA

skyzerr33

By skyzerr33,
in Western Australia

 Share

Recommended Posts

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Nizmo

they did it all at once - took car for drive - came back handed keys to me

Niz , I am still not convinced it is not a balance prob.

Only other thing i can think of that causes the symptoms you are describing ( note the service adviser type , non committed type reply :( ) is possibly loose front wheel bearings.

If I can get some time , I can come to your place or you come to mine ( with a chaperone if you don't trust me );)

And we can do some inspection.

cheers

ken

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Popular Days

Top Posters In This Topic

Popular Days

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by adam 32

ken; revised question...

can andrew tune it? do you know what interface they use? cos theres no external output on the ECU itself

Mate , I have never seen anyone in WA tune one yet.

Jash had one in bigred and lumpy couldn't tune it so it was binned for an Autronics when the engine was put in GTAAH.

I think it is done with smoke and mirrors:bahaha:

Cheers

Ken

ps try pm 'ing steve sst for a tuners point of view. He'sa cool and will give you a reasonably straight answer.

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Nizmo

yeah that would be good ken :(

What ??

good I come to you or good you come to me ?

I have a jack so the latter would prolly be better but bring someone with you ( aka Paul )

My wife is suspicious of what I do as it is and a gorgeous 6' 1" blonde calling to my place alone is not going to help at all:D

cheers

Ken

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Nizmo

ok if u want me to bring paul i will - yeah i'll come to u - um dont know what suburb u're in but wil work that out later :(

Paul has whaled here b4 , he knows .

Ps , pm ed you

cheers

Ken

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I am well aware as I did rant at him to buy a MX5, buy the 2.5 before he DIY'ed it, etc as well as do things to the holden. He will obtain a ND. It's the best of both worlds. They look great in person, definitely the best looking one. Just a matter of time now.
    • r32-25t
      NC MX5

      By r32-25t · Posted

      Remember this is the same person who said he’d never own an nc 
    • zique
      Ceramic turbine damage to engine - what did yours do?

      By zique · Posted

      ouch! how is the car now?I had sold my gtr but have been looking into some on trademe and a 260RS but I wouldnt be keen on any repairs needed on them
    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
×
×
  • Create New...