Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by Adrian_perth

neo, thought i'd give ya an idea as to what i am getting for my new exhaust :- hks hiper/blitz nur spec catback system

                     :- 3 Inch Highflow cat

When you gettin that Adrian. Will be good to see some at the cruz. I swear people must think that i steal skylines. I look under then all everywhere. freak!

Originally posted by Neo

When you gettin that Adrian. Will be good to see some at the cruz. I swear people must think that i steal skylines. I look under then all everywhere. freak!

i do it all the time. or pull a hard u turn while im driving to go and check a good looking import out :P

i love the funny looks u get :D

Psiker

i don't have it yet neo, but if all goes well i have my plans set out and mods should start hopefully next week if all goes to plan :D

at the moment i only got blitz filter, apexi front pipe and trust catback getting rid of front pipe and catback for new shit though :P

adrian :D

Originally posted by Adrian_perth

im turning 18 in august :D it's hopefully gonna go hard! i seriously wanna change it to manual but then again i'd get a better time with the slush box :P and maybe if i get that new turbo it will go even harder :D

adrian :P

wow RESPEKT!:uh-huh:

when i was 17 i had a 1991 TR magna, Auto, 2.6l 4 cyl

did u get the loan and all urself or buy outright with savings?

Psiker

Originally posted by Adrian_perth

i don't have it yet neo, but if all goes well i have my plans set out and mods should start hopefully next week if all goes to plan :D

at the moment i only got blitz filter, apexi front pipe and trust catback getting rid of front pipe and catback for new shit though :P

adrian :D

i thought apexi front pipe was good though? or u just want it to be the same the whole way thru?

Psiker

the catback is shit i cut on resonator and middle muffler sounds alright but i done like the welding and shit looks dodgy the muffle is tiny inside as well

apexi frontpipe is meant to be good, but it's only 70mm i dun think that is 3inch :P

adrian :D

Originally posted by Adrian_perth

my parents GOT the loan for me, BUT i am paying for everything, i was too young to tak out a loan so just got them to do it, no way would my parents pay for it :D

adrian :P

wow nice parents. my parents will go gaurenteer me (speling) but they wouldnt take a whole loan for me. specially with the houses and cars and the boat (now gone :D )

Psiker

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...