Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by Nizmo

well im off guys n girls

*kisses Paul*

*hugs everyone*

Sweet dreams everybody :angel:

BYE

Bye Niz.

Hmm kisses for pwpt60secf.

Is there something going on I don't know about?

Cheers

alszcheimers

Ken

paul - no joke.. hope u like bombay saphire.. i wanna be there to see u finish the bottle tho.. :)

aidwin - tune is much better.. heaps stronger down lower - still get a little surge tho - i've got suspicions it could be faulty wiring with the itc.. tune needs fixing cause can't run more than 0.65bar at the moment... didn't get a chance to ask bout the power fc - he was too busy to even let me pay him when i picked the car up.. all for free so far.. hehehe :(

As per my post I'm doing a few cosmetic things now, like I've had a set of side skirts since november last year that were meant to be put on before I went to the UK in december that still arnt on yet :( Plus paul has some rims for me, then I think a catch can after seeing the oil in the intake manifold today and a ogura flywheel as well :)

Originally posted by gtrken

Bye Niz.

Hmm kisses for pwpt60secf.

Is there something going on I don't know about?

Cheers

alszcheimers

Ken

Yeah i know - they werent even appreciated so it'll be the last time i do that haha

I'll ride with anyone who wants to give me a lift - beats walking anyway haha

**gone for good now** Later peeps!

paul - sweet... zanda will probably be wanting to come too... i supose we can't have too many people otherwise accomodation will be hard to find...

as for drinking - i'm sure i'd be up for that.. would like any chance to drink u all under the table.. :(

aidwin - cooler is on the cards.. some guy got 275rwhp with the same setup as me, well close to it, cept he had a front mount.. so for an extra 25hp it could well be worth it.. me don't want to sacrifice low down power tho....

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...