Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by macka

Hendo=bang

I think most of em are 11s ever heard of feeler gauges without making a smart comment fatboy?

And SST , and Race torque , and speedworks and....

There all not perfect Macka so lets not go there.

Cheers

Ken

Originally posted by Micko

Any dramas with running the plugs i got till monday?

As i said earlier i took the car for a drive & it seemed aok. Then i can double-check with steve before i shell out any more coin:)

I wouldn't think so as long as you drive the commode.:P

Cheers

ken

Originally posted by macka

well why ask the question bonehead

your plugs are fine if thet diont ping

Kriky there plugs they dont drive the ball mill for the biggest Gold crushing mine in Australia

Fair enough - I just want to be able to understand HOW they can affect performance

BTW - you are an asshole

Originally posted by macka

well why ask the question bonehead

your plugs are fine if thet diont ping

Kriky there plugs they dont drive the ball mill for the biggest Gold crushing mine in Australia

Have another the sphincter of the universe macka.

Ohh and a chill pill...:P

Cheers

Ken

Originally posted by macka

anyway....

I think adam32 is a young Micko in the making what do u reckon Kenny?

Nah not even close , Micko keeps his paranoia in whoretown, Adam spreads it across 2 forums.

cheers

ken

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...