Jump to content
SAU Community

Whoretown WA

skyzerr33

By skyzerr33,
in Western Australia

 Share

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Popular Days

Top Posters In This Topic

Popular Days

Nizmo Grand Master

Nizmo

Posted
Posted

well i promise russ all access pass even if he wants backstage :) haha

Ken pauls scratch was his own fault - he was trying out his wrestling move he used to pull on his sister and was crushing my hand - so there was a little nail dig to warn him to let go then there was a bit of a chunk taken out - he quickly learnt that i was not his lil sis :)

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Nizmo

apart from Liz Hurley i thought most UK women were ugly - thought i would go over there cos there would be less competion *meow* hehe :)

the guys on the forum think you are far better looking. Cos they think they may have a chance as opposed to NO chance with Liz Hurley:rofl:

Cheers

Ken

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Nizmo

well i promise russ all access pass even if he wants backstage :) haha

Ken pauls scratch was his own fault - he was trying out his wrestling move he used to pull on his sister and was crushing my hand - so there was a little nail dig to warn him to let go then there was a bit of a chunk taken out - he quickly learnt that i was not his lil sis :)

Hmmm , wouldn't that be incest if you were....:bonk:

Greg it was the Ricer , not the Racer but still surprised them and me.

Cheers

Ken

Nizmo Grand Master

Nizmo

Posted
Posted

but Liz Hurley was pretty plain to begin with and she had these massive over grown eyebrows - she starred in this airline hijacking movie - u only have to watch that to see what a good stylist can do.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...