Jump to content
SAU Community

Recommended Posts

haha my ex goes hard and he's 29.

yeah its so expensive to go out .... drunker u get the more money u blow haha i was just working out a budget just then .... i want to get all my bills paid off cos once ive done that im a rich girl .... but its all going towards my europe trip next year .... none for car ;) oh well as long as i can still beat Hondas im happy :mad:

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

well im just getting it all direct debited out .... my loan from my parents - i now have $50 coming outta my account and going to them each payday, $70 will be going into a savings account $100 will be going off my credit card

The rest is mine to play with how i wish - but to tell u the truth it'll probably be going on bills as well haha. got my insurance due soon so that'll be direct debited outta my account each month.

hehe and Dr Claw (inspector gadget) ive got a picture of Dr Claws cat in my head.

im pretty good with my credit card - its just i had an accident 3 years ago - i sideswiped a Telstar in my ZX - he sent me a bill for $1,300 and so that went on my credit card!! haha and it was so hard for me to pay it off earning the crap money i was earning .... now im earning better money im still in 2.5K worth of debt on my credit card but slowly getting it paid off .... almost be off if it wasnt for the fact i just put a set of tyres on it!!

yeah my cars looooow for a skyline ;) haha my exhaust sits about 4cms off the ground :mad: looks good tho ..... GTR kit, 17 inch rims. Ace!

im an admin assistant for the international trade & investment services dept. Before that i worked in the car industry for three years

I earn a lot better money in govt yes :mad: for my age anyway - i earn between 33 - 35K a year

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...