Jump to content
SAU Community

Recommended Posts

Originally posted by Micko

How many k's tonight ken?

Getting the ecu tuned tomorrow?

Let us know the outcome eh?

Nope , run in and been at Lumpy's getting the chip re rit for a 7500 rpm revlimit and plenty fuel

Cheers

Ken

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by zanda

checkin up on your dafaming ass!!!

hey ken, rob, micko.

hey ken,

how often do good deals on 2nd hand racing seats come up on your auction site?

Plenty on the jap auction but shipping is the killer.

Paul , am doing the Full Monte rally which is like the classic rally but 1/2 the price.

Cheers

Ken

Originally posted by GTS-t VSPEC

Alex, It's only defaming if it's not true:p

Phil, I ain't scared:D

Ken, How many K's till you can let her rip?

Already have , 1000km and I clocked that up last night after 3 nights cruising ( !! ) the freeway.

It's 69 km from roundabout at Baldivis to Hodges dve.

Cheers

Ken

Originally posted by Micko

Ken - no autronic yet?

Nope cos there's not time to tune it.

Paul the 7500km was put in tomight after I run it in at less than 7K .

Long process involving lots of part boost , 3 , 4 then 6 k rev limit and other crap.

Feels strong so may have been all worth it.

Cheers

Ken

Originally posted by GTS-t VSPEC

Ken, Sounds good, wish I was there to film it:( Good luck with it though, is the Mrs navigating?

Nope this is a seriuos navigation event and I would prolly abuse her.

Got some dude who had the 1/2 entry fee.

Cheers

Ken

Originally posted by GTS-t VSPEC

Ken, It had better be worth it after all of that:D What does the engine bay look like? Nice and ricey?

Yea , pretty blue cover and polished intake and terb pipes.

hpc type coating on terb exhaust housings and manifolds.Works well , bugger all radiated heat.

Cheers

Ken

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
×
×
  • Create New...