Jump to content
SAU Community

Recommended Posts

To add a bit of variation, you can count me in.

Marc2

Awesome, 2 stagea's will keep the people guessing.

We'll have to get a spot next to each other

"why are they different, but the same?"

  • Replies 182
  • Created
  • Last Reply

Top Posters In This Topic

I think a thread was posted somewhere about this earlier, but im too lazy to go and find it  B)

Anyways, what is it you ask? Heres a run down....

So its basically a mini car show in Canberra that runs for just one day. Entry is free, and you can come and go as you please.

Anyone interested in going and representing for Nissans finest? If so ill start a list, maybe we can get 10 - 15 cars to come along?

1. Amaru

2. SkyGTRline

3. Terminal Stagea

4. mickGTR

5. Frink

6. Terminal R33

7. race_snooze

8. LTSjayce

9. leech_

10. djhatton sexy blue beast if the traitor hasnt sold it :)

11. NathR32

12. Supafly Skyline

13. ib6ub9

14. marc2

15.

I finally have the Beast Registered so i will be there :P

I could write a book on the hardships of getting the R over dickson.

  • 3 weeks later...

I've just found out i have a taekwondo tournament on that weekend. this is a shit, first i missed the show'n'shine because of a tournament, and now i'm missing this one.... such a bugger!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...