Jump to content
SAU Community

Recommended Posts

MASSIVE UPDATE 24/4/06 !! !! !!

LOTS OF RANDOM PARTS, - WRECKING RB20DET - CA18DET - TURBOS - INJ - AFM - SENSORS -

RB20DET $

bare rb20det head 100 firm- very good condition only apart as bottom end had bearing noise

plenum 45 - fuel rail and six injectors included

rocker covers 30

throttle body 25

270cc top feed high impedence injectors $5 each or 6 for $20

cooler 20

rb20de exhaust manifold (non-turbo) - $35

CA18DET $

370cc inj 40

intercooler 20

dump 5

f/pump 15

mirror 45 - works fine, drivers side black

calipers X2 $25 - 2 spot calipers, lines, free pads and rotors (just no RWC)

contact : shaun - 0403155282

post-2503-1129163863.jpg

------------CA cooler---

post-2503-1129164032.jpg post-2503-1129164064.jpg

------RB20 plenum---------------RB20 TB----

post-2503-1129164128.jpg post-2503-1129164178.jpg post-2503-1129164226.jpg

------RB25 rockers---------------Rb25de manifold----------T28 blown seal

post-2503-1129127693.jpg

post-2503-1129127729.jpg

post-2503-1129163956.jpg

Edited by shaunr32
Link to comment
https://www.sau.com.au/forums/topic/89228-wrecking-rb20detstock-ca18det-parts/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

i have no pics yet as i have no cam. they are a factory option 10 stack sony and 6 stack adzrst with head units to suit. no head unit to stacker cable. all working when taken out and if they do not work i will give your money back minus postage or whatever.

where are you located

$50 per one item or $50 for all stez items

shaun

  • 2 weeks later...

hey shaun,

you wouldnt happen to have the cold start control valve for the RB20DET by any chance at all would you

Thanks in advance

Sop

Edited by RB20SX

sop - what does it look like - i will have it. its yours

i am wrecking the engine that i was going to sell you - it blew up, just as well i gave you the other one. how is the rb20sx going??

killemaul - no ac compressor - soz

pics will be up tomorrow - i finally got a digi cam !!

shaun

tomorrow is now today and the new pics are up.

just to add i do have ceffy center console and handbrake

and a few of the prices i have had to make up so the mods dont get me.

make an offer on anything - the worst i can do, is tell you to go --<<bunch of flowers>>-- yourself in the arse

cheers

i am sure they are identicle, as i have the rb20 turbo manifold on my rb25 at the moment, waiting to be registered with rb25 then i will be selling it in about 2 weeks

ill let you know

sorry for the whatever

shaun

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...