Jump to content
SAU Community

Havung Some Trouble With My Gtr

Zardos
 Share

Recommended Posts

Zardos Community Regular

Zardos

Posted
Posted (edited)

I was driving home about 10 minutes ago and I gave it some stick, (in the legal speed limit of course) and all of a sudden my car started to sound almost like a WRX.

Even when it's idling and I tap the pedal.

And it had lost a lot of power

There was no smoke at all and temps where all normal.

My car is standard apart from a zort and panel filter, and 10 PSI boost.

It's a 1991 model with 140KMs on the clock.

The motor it self is only about 33,000 KMS old.

Making 221Killowatts at the rear wheels.

Also the mechanic noticed oil was leaking from the back of the second turbo which was due to be repaired with in the week.

I’m not that experienced with GTR's so this is a bit of a worry to me as I have not long owned the car.

Any help would be great.

Edited by Zardos
Link to comment
https://www.sau.com.au/forums/topic/89584-havung-some-trouble-with-my-gtr/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

Well, if you are really worried about the motor you need to do a compression test. But probably the easiest place to start is to pull the spark plugs and replace any that look fouled. If you have a compression gauge you can check that at the same time.

mrjelly Apprentice

mrjelly

Posted
Posted

yeh happened to me too! was driving, then all the sudden car was sounding that a wrx. i thought it was mad at first but realised it lost alot of power n didnt feel the same. did compression test, found out one of the spark plugs was gone, so it was pretty much running on 5 cylinders..

Zardos Community Regular

Zardos

Posted
  • Author
Posted
yeh happened to me too! was driving, then all the sudden car was sounding that a wrx. i thought it was mad at first but realised it lost alot of power n didnt feel the same. did compression test, found out one of the spark plugs was gone, so it was pretty much running on 5 cylinders..

What number cylinder died on you?

When i change my coils i am going to also change my turbos. One of my turbos is leaking oil, (second one) which are still under wantry so iam going to get both checked and if needed get both re-built. Which iam going to sell them because i am going to get a pair of N1's and change ECU while iam at it..

If any one is interested in buying them PM me...

mrjelly Apprentice

mrjelly

Posted
Posted
What number cylinder died on you?

When i change my coils i am going to also change my turbos. One of my turbos is leaking oil, (second one) which are still under wantry so iam going to get both checked and if needed get both re-built. Which iam going to sell them because i am going to get a pair of N1's and change ECU while iam at it..

If any one is interested in buying them PM me...

it was the third cylinder... thats wat the compression test showed...

well when i had those checked out, i also found a rattling sound inside the engine. apparently tensioner was worn out n loose, needed replacing. also i had to change one of the cams coz it was cracked and change timing belt. these cars man... haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...