Jump to content
SAU Community

Recommended Posts

Alright ... newbie coming in, some one plz tell me who lives round Sydenys South West ... like Quakers Hill Castle Hill Places like that ... cause if i dont race im gonna go crazy here. If you can put up with a noob for awhile i promise i want bug u too much. :)

Edited by ^De_LiL_Devil^
Link to comment
https://www.sau.com.au/forums/topic/90954-sydney-south-west/
Share on other sites

isnt' castle hill east? like near coogee?

LOL..

castle hill is like up northwest.. relative to me..

liverpool is west..

dont be silly and request that you want to race.. as someone has said leave it for the tracks or drags..

what car do you drive?

Skyline GT-R34 ... well sometimes ... im not suppose to but it dont stop me, im allowed to once im off P's ... lol ... Eastern Creek is West way west ... castle hill is north ... not quite as west as me ... try quakers hill or furhter

castle hill is north west man.............and don't be an idiot.........if you wanna race, go to  the race track

I was racing at 14 in america .. like im gonna change now .. only prob is i didnt have a liscence then and now i have to wait three years to drive MY car not my parents ..

Edit: for all those who read the 'i wa drivin at 14 in america' .. its was my besty, Jes, she gave me this site so i use it now not her ... My names Felcity and i've not been drivin long ... jst round carparks and that til i get my lisence on friday 28/10/05 ... Jes was the racer since she was 14 ..

Edited by ^De_LiL_Devil^

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...