Jump to content
SAU Community

Recommended Posts

Guys,

Ive posted before asking if my setup will make 350AWKW, know id like to know the following:

Will the facotry ignition system keep up?

What spark plugs and what gaps?

Will the R33 GTR pump keep up?

What gearbox Oil?

What Front Diff Oil?

What Rear Diff Oil?

To refresh your memmory my setup is

RB26 Head Mildl Ported and Fully Rebuilt

HKS Step 1 272 Cams

HKS Cam Gears

Nismo 600cc Injectors

Apexi Power FC

Nissan Q45 AFM

R33 GTR Fuel Pump

Nismo Adj. Fuel Reg

GCG XTR T60 Turbo

GCG XTR 55mm Wastegate

Custom Manifold (Equal Length)

100mm Thick Cooler

14-Row Oil Cooler

RB30 Bottom End

O-Ringed Block

Head Restrictor Etc

H-Beam Conrods

CP Forged Pistons

ACL Race Series Bearings (Heat Treated Ones)

Straigh Through Exhaust System

Twin Plate Clutch

All this is going into my R32 GTR with a standard R33 GTR box. I dont think ive missed anything let me know if i have

Cheers

Edited by GTR_Junkie
Link to comment
https://www.sau.com.au/forums/topic/91191-some-questions-about-my-new-setup/
Share on other sites

sounds good.

redline oil heavy(red one) in gearbox and diffs.

coils shouldnt be a problem but you may need to gap the plugs down

id use a iq22 denso.(7 range in ngk,0.4mm iridum.)

fuel pump wont cut it.

injectors will be at there max.

youl need a much biger oil cooler

stock pumps are at there limit around 370-390rwhp.

just put in a bosch 044(rated at about 600-700hp) i think.

go easy on the stock box as 3rd gear is weak as shit, not fun to change believe me.

Injectors at there  max ???? and a bigger oil cooler??? Maybe i should have stated it will be street driven not track raced or anything

Thats not what u said in ur other threads on the same subject.

A 350rwkw GTR is a waste of time and fuel driving as a daily driver on the road these days.

330rwkw 600cc injectors at 90% in my old motor.

oil temp with properly ducted 25row oil cooler still gets up to 115deg from brooklen to berowa. about 5mins flat out.(sock 32gtr)

id run a external 044 with a surge tank etc(unless you always have a 1/4 tank)

if you are going to do it you may as well do it properly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...