Jump to content
SAU Community

What Is Better Rb30et Or Rb25det

AAA34T

By AAA34T,
in Classic & Vintage (1950's-1980's)

 Share

Recommended Posts

Adam_RSX Proficient

Adam_RSX

Posted
Posted

I say go with an RB30E + T, it would be far more driveable in everyday driving, I think it would probably be better in the hills with extra torque compared to a bit of extra breathing ability and I'd have to think it would be far cheaper and just as reliable as an RB25 at the power levels you're after

AAA34T Community Regular

AAA34T

Posted
  • Author
Posted

I am sick of the power that the car has got now i want easy 13 sec quatermile. I am happy with that so what ever it takes i wont say no if it goes quicker but it must be very reliable. i hate cars that have had all this money spent and they live in a work shop.

george.bryant Rising Star

george.bryant

Posted
Posted

rb30det seems logical. Is there such a thing as a RB30et anyway?

RB30e Block rebuilt with a RB25DET VVT head on it would be the way to go i reckon. It is a very debateable topic...

I've attached a RB30DET build guide.

RB30_DOHC.pdf

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
How many rb25's blow up their ringlands at 250rwkw, vs rb30's that still have stock internals that survive at that power?

why is it that the top few spots of the r31 club have 100% STOCK rb30E bottom ends, except for a rb25 with forgies and gtr rods that can't even make top spot on c16 and semi's :angry: hehe

dunno who was using c16 and semi's... but it certainly wasnt me :)

And there are plenty making 250rwkw these days on stock RB25 (more actually)

Beats having to spend $$$$ on lots on SOHC head work :blink:

And what does the r31 club time have to do with it again?

Ifwe wanna get technical we can

slow_r31 Collaborator

slow_r31

Posted
Posted (edited)
dunno who was using c16 and semi's... but it certainly wasnt me    :D

And there are plenty making 250rwkw these days on stock RB25 (more actually)

Beats having to spend $$$$ on lots on SOHC head work :D

And what does the r31 club time have to do with it again?

Ifwe wanna get technical we can

was just some tongue in cheek stirring, nothing meant by it, i acutlaly thought u used c16 for that time, my bad.

the point with the r31 times was just an example that rb30E bottom end is just as strong and can take just as much power. im sure there are examples both ways however.

i have a RB30E+T, its done 200,000k's, gives me 10L/100k's fuel economy, has shit loads of torque and makes ~160rwkw everyday.

both motors are reliable, and ull make your 180rwkw on stock turbo/injectors, the only real difference is slight cost difference, and the feel of the motor

go for a drive in both and see which u like, the torque of the 30, or the revabilitly of the 25.

Edited by slow_r31
spx25t Community Regular

spx25t

Posted
Posted

I would recommmend the RB25DET I have one fitted in my R31 using a turbo of a VG30DETT which I believe is the same size as standard just Ball Bearing running 14psi it makes 183 kw's at the wheels and I have run a best of 13.3 over the 1/4 @103MPH using cheap street tyres(TRX Rims for racing 17's for the street) my car weighs about 1400 kgs. For reliability I have been running that boost level for the last 18 months(54,000kms) since I purchased the car and it has not missed a beat once.

I have been to 2 Powercruise events each one consisted of 4 days(ECR). Drag Combat twice (WSID) and about 5 or 6 Street meets (WSID). all that plus I drive the car everyday to and from work which is about 400+ kms a week and I get just over 400kms to a tank of fuel.

: ) hope this helps somewhat with your decision

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...