Jump to content
SAU Community

Recommended Posts

I agree, the standard coils would be the weak link but not to a major degree.

This being said the coils are not too expensive anyway and worth the expense if your in a high HP bracket, otherwise I don't think that its worth it.

Mercury Outboard coils are @$75.00 each x 6 = $450 plus leads, brackets and other installation costs.

Maybe the money could be spent on mods to take advantage of the extra spark, ie; a tune which I beleive will give an overall better result.

If budget allows - get everything!

What was the actual part number of the mercury outboard coils you where looking at?

I'll see what i can do to track down some of these - if i purchase lets say 10 of them or something then hopefully we could get some kind of discount.

Here is a picture of the Mercury Outboard Coil

Mercury_Outboard_CoilF69858.jpg

Part No: 339-832757A4

Best Price I could get were @29.00 US from the states.

Just got confirmation on shipping charges and convertered it to AU

AU$40.00 each

AU$94.00 shipping for 6 coils

Total: $334.00

Edited by WetGTR

i'm quite interested. so with the 6 mecury coils, you just need the msd DIS 4 to run them? I'll be very interested to see if it works with a PFC.

You will have to find out if the PFC has output drivers to run the MSD Unit.

I have also heard that you shouldn't run the Mercury Coils from a MSD DIS-4, can't take it and blows up. Something about the coils having almost no resisstance.

WETGTR, With the autronic SMC and the CDi you run three outputs from the computer into the CDi then run coils like the 4AGZE style with two leads from each coil using three outputs from the CDI (three 4A coils equals six cylinders work of spark plugs) and you dont have to run in a waste spark mode.

WETGTR, With the autronic SMC and the CDi you run three outputs from the computer into the CDi then run coils like the 4AGZE style with two leads from each coil using three outputs from the CDI (three 4A coils equals six cylinders work of spark plugs) and you dont have to run in a waste spark mode.

The 3 output drivers from the Autronics will give you no other choice then to run wasted spark. The only other way would be to replace the ECU with something that has 6 output drivers and a CDI unit that has 6 input drivers.

It's not the coils that will make any difference, it's the ECU & CDI unit. The coils are just the dumb unit and spark when told to by the CDI.

Note: the MSD DIS-4 is only a 4 driver unit so on a 6 cylinder car you can only use 3 drivers which means you'll be runing the wasted spark setup. The Autronics CDI has only 4 drivers aswell.

I know the Motec ECU and CDI's run 6 input & 6 output drivers.

What about the the HKS twin spark thingy dose that need output drivers to run the Unit.

They work off DLI for correct timing and sequence for spark plug control . The DLI system is integrated into your ECU or you have a dwell board controlling igition. The outputs I was speaking of are only for CDI type of igition.

Basically their are 2 types of systems out there:

1. DLI

2. CDI

from what I know anyway.

The HKS DLI will work aswell but I think the benefits of CDI are work it eg: higher spark energy, longer duration spark, multi spark.

You will have to find out if the PFC has output drivers to run the MSD Unit.

I have also heard that you shouldn't run the Mercury Coils from a MSD DIS-4, can't take it and blows up. Something about the coils having almost no resisstance.

What blows up the MSD or the mercury coils?

Hmmm...

So what coils can you use on the MSD without something going bang? lol

What blows up the MSD or the mercury coils?

Hmmm...

So what coils can you use on the MSD without something going bang? lol

The MSD CDI fails.

Check this link from the EFI UNI

http://efi101.com/forum/viewtopic.php?t=31...75c8a102322abca

Checkout this link for some good information regarding CDI and other related spark information.

http://efi101.com/forum/viewtopic.php?t=39...hlight=msd+dis4

You will still run waste spark with the 4agze coils but only on one cylinder. Its better than running one or 2 coils for the whole system, nothing wrong with waste spark on a drag circuit or high hp application any way as you should be checking the plugs all the time!!!

You will still run waste spark with the 4agze coils but only on one cylinder. Its better than running one or 2 coils for the whole system, nothing wrong with waste spark on a drag circuit or high hp application any way as you should be checking the plugs all the time!!!

I agree with what your saying. I beleive a good setup would be to have a single coil for each spark plug so say a 6 coil setup for a 6 cylinder car.

I think you have to think this through in regards to CDI as I don't know if all ECU's have the output drivers to run this type of setup. Because CDI works differently then Inductive systems.

I know that with the Autronics you have to add in a dwell board just so it can work with inductive systems which skylines have. You then have to go into the ECU's software and change the +ve trigger to -ve trigger.

Not too hard but not as simple as just remove the ignitor, plug in a CDI and on the way you go.

Another thing about CDI is they are an invertor type unit which transforms 12V to 450V-500V so its going to get hot. A quality item will last.

Check to see which coils will work well for the CDI you wish to use.

Hmmm...

So what coils can you use on the MSD without something going bang? lol

Not sure with the MSD but maybe the Bosch coil or the MSD Coils should do the trick but you have to check on this.

I have the bosch Part no if you need it @$44.00 each and has been highly recommended. Available at most bosch outlets as they are used on Fords.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...