Jump to content
SAU Community

Recommended Posts

I went to dragstrip last night and managed dissapointing time of 13.8s, 109mph (175km/h)...car is r33 with bigger turbo (its T-57) making 347hp atw ON 15psi, and i expected at least low 13s...traction was shit 60 foot 2.478 sec, with shit trampio tyres at the back 18 inches 265 wide, tyre pressure at 40psi (stupid me checked today tyre pressure)...what do you reckon the car should do with this mph, and what launch methods u using, i managed best 60ft without much throttle at take off and whenever i upped the revs i couldnt do better time than 2.6 60foot...i noticed as well that gear stick was sticky on second run, i needed to push really hard few times to get it in third gear, still beat wrx hehe...what could the reason be? i suspect when car was brought here from japan while compliancing all the fluids have been changed except gearbox oil so it could be too old?

Link to comment
https://www.sau.com.au/forums/topic/93500-dissapointing-quarter-mile/
Share on other sites

i have 225rwkw and got a 13.5 at 109mph... 60 foot 2.3 on 235/45/17

then the next week went back (same set up) and managed 13.1 at 110mph

then went back and got 12.71 at 111mph 60 foot of 1.93 on the same tyres...

just go back and practice...

by the way i launch at 6 grand

hope that helps

i have 225rwkw and got a 13.5 at 109mph... 60 foot 2.3 on 235/45/17

then the next week went back (same set up) and managed 13.1 at 110mph

then went back and got 12.71 at 111mph 60 foot of 1.93 on the same tyres...

just go back and practice...

by the way i launch at 6 grand

hope that helps

is that a 6000 dump or u let it ride a little

is that a 6000 dump or u let it ride a little

i ride it a little. best way to explain would be that i let the clutch go in one fluid motion over a period of about a second or a bit less.

don't hit the limiter it will die in the ass before you grab the next gear... your MPH indicates a mid to high 12 sec pass if you can get the 60ft time down to 2 flat...

I suspect your suspension setup to be at fault... common errors for drag are too stiff a rear suspension and too much neg camber at the rear as the car has been lowered? modern IRS cars don't like to be lowered or you will just fry the insides of your tyres... which is even worse with wide tyres... get some camber adjustment bushes should help get the beast off the line

i have a feeling if i had 50hp less i would have done better time

i have 225rwkw and got a 13.5 at 109mph... 60 foot 2.3 on 235/45/17

then the next week went back (same set up) and managed 13.1 at 110mph

then went back and got 12.71 at 111mph 60 foot of 1.93 on the same tyres...

just go back and practice...

by the way i launch at 6 grand

hope that helps

what revs is rev limiter at

don't hit the limiter it will die in the ass before you grab the next gear... your MPH indicates a mid to high 12 sec pass if you can get the 60ft time down to 2 flat...

I suspect your suspension setup to be at fault... common errors for drag are too stiff a rear suspension and too much neg camber at the rear as the car has been lowered? modern IRS cars don't like to be lowered or you will just fry the insides of your tyres... which is even worse with wide tyres... get some camber adjustment bushes should help get the beast off the line

suspension does feel stiff, its tein not adjustable suspension, no camber kit

don't hit the limiter it will die in the ass before you grab the next gear... your MPH indicates a mid to high 12 sec pass if you can get the 60ft time down to 2 flat...

I suspect your suspension setup to be at fault... common errors for drag are too stiff a rear suspension and too much neg camber at the rear as the car has been lowered? modern IRS cars don't like to be lowered or you will just fry the insides of your tyres... which is even worse with wide tyres... get some camber adjustment bushes should help get the beast off the line

I went to dragstrip last night and managed dissapointing time of 13.8s, 109mph (175km/h)...car is r33 with bigger turbo (its T-57) making 347hp atw ON 15psi, and i expected at least low 13s...traction was shit 60 foot 2.478 sec, with shit trampio tyres at the back 18 inches 265 wide, tyre pressure at 40psi (stupid me checked today tyre pressure)...what do you reckon the car should do with this mph, and what launch methods u using, i managed best 60ft without much throttle at take off and whenever i upped the revs i couldnt do better time than 2.6 60foot...i noticed as well that gear stick was sticky on second run, i needed to push really hard few times to get it in third gear, still beat wrx hehe...what could the reason be? i suspect when car was brought here from japan while compliancing all the fluids have been changed except gearbox oil so it could be too old?

it's all about the first 60 foot. 2.5 is way too high to be able to run a low13/high12. i am pretty sure it's just a practice thing. and lower your pressures to about 24 psi. that will help a shiteload :(

Dump the 18's get some sticky street tyres on some 16's,select correct tyre pressures,change over your susp for some 90/10 's pedders,take the spare and any thing else loose out of the car,i would lightly slip the clutch on initial drop, short change into second,dont drive to limiter in 2nd then give it all you have got in 3rd and hang on,drop into 4th if you need it.The biggest mistake every one makes is using too much 1st and 2nd gear these only result in excessive wheelspin- hence your slow 60ft times,3rd gear is the one that does the driving and you must get up into it as soon as posible!

Anyhow good luck with your future racing (remember is not the out right hp but the way in which you hook up! )

Regards,

SKYLINE (Kym)... B)

Edited by skyline

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...