Jump to content
SAU Community

Recommended Posts

Does anyone know if this engine will fit into any of these cars?

Depends on what you mean by 'fit'. It's certainly not a bolt in proposition, but with enough time and $$ anything can be done. One of these has been shoe-horned into a 240Z. One problem is that there are no manual gearboxes that bolt straight up, so an adaptor plate would be required. Of course, doesn't matter if you stick with the auto.

Yeah, don't like your chances. John looked into that but if you saw the custom headers that had to be made to squeeze past the chassis rails then the turbo option quickly evapourates. Thats why he went down the supercharging path.

There's a VH45DETT in a S14 thats being built here in QLD, running twin XR6 turbos, custom plenums etc...

Very tight fit, turbos are located behind the headlights, inner guards have been cut to make way for the exhaust manifolds etc...

Be interesting to see how it goes once finish :)

There is a 300zx up here with one in it. He has used the 300zx manual gearbox with it, as thats what was in the car to start with from memory. I guess the major problem you will have is with the width, not so much the lenght.

There is a 300zx up here with one in it.  He has used the 300zx manual gearbox with it, as thats what was in the car to start with from memory.  I guess the major problem you will have is with the width, not so much the lenght.

Is that the orange one?

Yeah the S14 I mentioned is running a VG30dett box aswell.

Twin xr6 turbo's on a 4.5 litre will see decent boost by maybe 5500rpm..

Haha, be an interesting ride for sure once on boost.

Ok, well i was thinking to fir the engine up into a car, leaving the engine standard using Twin T04Z and the other assosciated bolt-on's, and once it grenades just removed and re-build it or buy another engine.

Should be good for over 1000hp me thinks, the car will be used as a drag car but i want to keep it registered and engineered as i would like to be able to drive it on the street every now and then

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...