Jump to content
SAU Community

2rismo In Current Hpi

TTT

By TTT,
in New South Wales

 Share

Recommended Posts

TTT Grand Master

TTT

Posted
Posted

very decent results with your car there mate.

I have a question and I guess it is more of a technical question though..

with all the talk of skyline turbo's and ceramic wheels dieing over x psi and so forth..

your's at 14psi and still going for god knows how long and according to the mag, more than 100 1/4 passes in that form..

common theory of the ceramic exhaust wheel breakage is too much boost which results in too high exhaust temps which break them.

so with the use of NO2, what effect if any does it have on the exhaust temps?

is this the reason for your turbo still living today?

also, is your NO2 disconnected in someway when outside WSID?

what sort of boost is dialed in during street driving?

thanks and all the best.

Link to comment
https://www.sau.com.au/forums/topic/93610-2rismo-in-current-hpi/
Share on other sites
2rismo Grand Master

2rismo

Posted
Posted

Exhaust temps actually go up with Nitrous Oxide usage. Boost spikes to 14psi on the bottle but only very briefly. Over-speeding of the turbine wheel can cause it to delaminate from the shaft - not always JUST heat related.

I don't drive around with the bottle in the car when I'm on the street and when I drive to the track it certainly isn't connected. Theorhetically I should also have the solenoids isolated with blanking jets but that sounds too much like hard work to me :D

Boost for street driving is usually your regulation 8-9psi with the EBC turned off. That's where it lives most all of the time. Off.

Thanks heaps guys, girls and pusseh boys like brett :)

Adrian

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
×
×
  • Create New...