Jump to content
SAU Community

Recommended Posts

Item: R34 GT-T Intercooler, standard

Location: Adelaide, South Australia

Item Condition: Excellent, used

Reason for Selling: Upgraded to Apexi front mount intercooler

Price and Payment Conditions: $230 excluding postage

Extra Info: Comes with the 'rare' plastic intake shroud

Contact Details: PM me, 0427 803 556, or [email protected]

Will post anywhere in Australia, buyer to pay postage costs. Maybe TNT Express is the way to go, or Australia Post registered? (that way you get a consignment number and tracking facilities)

Comes fully flushed & fin-picked only around 1500kms ago, so it is in excellent condition and order.

Great for up to 200rwkw - see 'R34 Intercooler' thread in the Stagea section.

Brendan

Link to comment
https://www.sau.com.au/forums/topic/94215-r34-gtt-intercooler/
Share on other sites

It fits a R33 & R34 definately......

& thanx to J_R32 for the infoon the R32 fitment.

I bought it only 3 months ago here on the forums and had it on my Stagea, but found a Apexi fmic on ebay for a price I couldnt refuse, so hence the resale of this R34 intercooler.

Brendan

It's not a straight swap for the R32, but it's only a minor modification. There's someone who did the job recently and they were charged approx $50 (?)for the labour involved to fit it.

Hey Brendan,

Just a few q's

1. 'Rare' plastic intake shroud, are you refering to the standard Stagea intake shroud? Or is this a custom made one?

2. Quote for postage up to Tamworth?

3. Wouldnt need another flush yet would it?

Cheers mate,

Chris

PM Sent....

1. rare shroud is a R34 shroud, a series 1 Stagea shroud is a R33 unit, therefore the R34 shroud is around 23% larger.

2. sent you an offer.

3. nup, perfect clean condition.

cheers for the questions AMS!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...