Jump to content
SAU Community

Recommended Posts

where can i get gauges to fit in a slot where a head unit normally sits as i have an empty spot after installing my new stereo, or can ya get like a plastic holder tray thingy to just put small pieces of paper, a little mobile phone and other miscellaneous items as a small storage type thing, its just i dont want a gaping hole in my centre console :rolleyes: and if you can get this stuff, where and how much ?

have u ever seen the inside of a GTR before? u do realise that u can buy the 3 guage cluster that sits in there... probably expensive unless u can find one second hand at a decent rate. im sure if u hunt around u can find something

I've seen someone on SDU manage to squueze 3 52mm gauges in the centre bit under the stereo.

Looked great. It was a very very tight fit, and I think he had to angle the gauges towards the driver slightly to fit them in!!!!

The problem with getting the GTR center doova is that it goes right up the top where the air con is. It has that corner bit (top right) missing to fit in there, but so does the air con :D

So if you move the air con down, or put the GTR doova under the air con, the middle one will have the corner piece missing as well.....

Another thing about the GTR console is that it takes 42 or 45mm gauges, which are hard to find. And there's no use using the GTR gauges cause it has the 4wd gauge on it which will be usless on a GTS-t :)

J

also jsut wondering,i have a pioneer 6450 head unit that i just installed today and i mounted it with the two standard screw holes on the bracket, and its a good 2 cms in the dash so its ugly at the moment, whats the best way of bringing it forward to fit snugly to the front ?

Scotty - you can get 45mm gauges here

http://www.omorimeter.co.jp/english.html

Don't know if they are any good or not, plus you'll have to mod the plate a little to get them in.

Anyone else know where to get 43mm gauges??

J

Or you could try this:

*3 Gauges on top

*Air vents

*Climate Control

*A/M Single din stereo

*Centre-console-plastic-compartment-holder-thingy-doova-tray-box

*Cig lighter / ash tray...

Just an idea :wave:

ps. the tray fits a mobile / charger / handsfree or small sunnies, but probably not all at once :) [a single din-sized box]

i dont mind the original, its better than any other car i have seen, but until i come across one i like better im sticking with the original, but i know i do need a new boot for my handbrake and possibly even the gear knob as they are pretty ****ed :P

btw just successfully install my two front 6"ers yesterday i did the head unit and the amp in the bootr, now im off to bunnings to get some MDF to raise my 6x9s on the back aprc el shelf, not to mention carpet it, boy o boy this is gunna be a pretty big job :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...