Jump to content
SAU Community

Recommended Posts

Hi everyone

I just installed an oil temp guage and was wondering what the normal oil temp should be while just driving around, ie crusing. With an oil cooler I should add. Today on the way to work was my first test and the guage barely moved from 40 deg (the lowest value). At first i thought i had wired it up incorrectly. Though after filling up the car I got back in and the guage read 60 deg. Then as soon as I start driving it went back down to 40 deg.

Does this sound like a normal temperature? Sounds low.

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/
Share on other sites

Weird

that is way too low.

The temp on a gtr sits around the 80 degree mark, which is very similar to water temp. then with a cooler once you get up and moving, it can vary between high 60's and high 70's depending on how hot it is, how fast you are driving, etc.

But ideally it should sit around the water temp mark unless you are giving it

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1735572
Share on other sites

Oil takes a long time to get up to coolant temp .If you only drive short distances it will never get up to normal temp .

If you drive it hard it will get a lot warmer than coolant temp and it depends on how hot the ambient temp is .

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1738567
Share on other sites

it sounds like your oil cooler is doing too good a job on the street. There are two options, one is to fit an 'oil-stat' or you can simply block off all or part of the core (just use a pice of sheet aluminium) for street duty, then remove it when you do drifting. ideally your oil should be above 70 degrees, but 80-90 is good. 40 or 50 is too low.

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1739382
Share on other sites

That was during the cooler periods

With the oil cooler, not once have i seen the oil temp hit over 90 degrees.

Prior to this, it would rise to about 95-100 or so degrees after a long highway journey (1hr+), continous revving @ 3k in 5th. Now, it goes down to around the low 70 degree mark

Oil pressure gauge at idle is close to 2, bit of throttle gets it up to around the 3 mark and the highest i think ive ever seen it is around the 4 mark

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1739386
Share on other sites

I actually think my oil temp guage is not working. Its a crappy Auto Gauge brand. The needle wobbles about all over the place. I guess thats what you get for buying a $30 guage. Gonna test it with a jug of hot water. If it doesn't give me a real reading its going in the bin.

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1743982
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...