Jump to content
SAU Community

Recommended Posts

my car was park at castle towers carpark tonight and when i come back to it after watching a movie, i find that theres screwdriver dents on the top of the door trim where some1 tryed to pry it open or something.

they didnt set the alarm off, or get in.. but it sh*ts me off, is that some fu*king low life has tryed to break into my car :P

not happy jan <_<

anyone know where i could get the door trim (the black strip that goes above the door), and how much would it cost to fix?

Link to comment
https://www.sau.com.au/forums/topic/97263-some1-tryed-to-break-into-my-car/
Share on other sites

Ah that sux... :P

You mean the rubber strip between the top of the window and the door thingy? or the plastic between the window and the door (ie. when you roll the window down that plastic strip)

Try justjap? or someone selling R33 parts?

lowlifes!

scary enough - i had been having problems with my central locking. It would lock but then would not unlock. Had to open my car using a screw driver and a coat hanger a few times until i had time to take the door trims off and fix the problem.

I took the lock barrels out of my door locks and filled the hole with arildite to make it a bit more difficult for some bastard to steal.

Now im a but scared because i can get into it so so easy.

Good to see ya car wasnt nabbed or anything taken.

Which car park at Castle Towers and where?

The original (old) cinema car park, or the new cinema car park?

Looks like what they've tried to do is push that button on the drivers side which unlocks the passenger door. Disable this switch asap if you haven't already. Take the door trim off and cut the wires.

Which car park at Castle Towers and where?

The original (old) cinema car park, or the new cinema car park?

Looks like what they've tried to do is push that button on the drivers side which unlocks the passenger door. Disable this switch asap if you haven't already. Take the door trim off and cut the wires.

new cinema car park on the top level

which coloured wires do ya have to cut to disable that? dun wana go cutting the rong wires, lol

is there any way you can activate electrical current through your door key hole when you arm your alarm so if someone tries to stick a screw driver into it it'll do a bit of damage?

theres an idea for alarm manufacturers!

is there any way you can activate electrical current through your door key hole when you arm your alarm so if someone tries to stick a screw driver into it it'll do a bit of damage?

theres an idea for alarm manufacturers!

rofl!! just hook up the 12v batt to the keyhole so when the alarms on it would zap any1 that touches it :) ... if needed put in a small step up transformer, for that added "ouch" effect :)

^_^

new cinema car park on the top level

which coloured wires do ya have to cut to disable that? dun wana go cutting the rong wires, lol

can't remember. Use a test light and see which one lights when you push the door unlock switch. :D

There is a thread somewhere.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...