Jump to content
SAU Community

Recommended Posts

Hi guys,

I've got a very noticable rattling in my rear suspension when going over bumps etc. I've got Apexi N1 Coilovers in there if that makes a difference.

Does anyone know where I should start looking to diagnose/fix the problem?

Link to comment
https://www.sau.com.au/forums/topic/97696-rattling-rear-suspension-r33/
Share on other sites

Uhm.. im not too sure. I bought the car a short time ago and it's got 60,000k's on the clock. So I guess they are between 5 and 55k's old :rolleyes:

Can shocks be screwed in that period of time? I guess they could!

The on the clock KM's may not be accurate, remember a lot of imports have been tampered with before they enter the country.

I've got N1's but havent noticed this problem as of yet.

But on the subject of N1's, are they a particularly good set of coilovers? A mate told me that brand new they are worth like $2500 or something - is this about right? They seem to have a massive amount of thread which will come in handy when i can be bothered lowering them.

Justin

Yeah i do realise that. The 'line that I bought had immaculate interior and was mechanically beautiful, so I am guessing that if it was wound back, it wasnt by much!

But the N1's are pretty good from what I have heard. Everyone says they are rock hard, but are a really nice shock handling-wise. Personally I dont think that they are that bad! I had a Supra which comes with bilsteins standard, which I found to be harder than the Apexi's! I guess it comes down to the setting of the damper rates too. They might be set unusually soft on mine?

.. They are adjustable probably farther than your front bar will allow - good for those car shows i guess?

There are many bushes in the whole suspension system. There is a bush at the bottom of the shock. Bushes on the suspension arms. Bushes on the swaybars.

Bushes absolutely everywhere.

It could honestly be anything. It could be a slightly loose suspension bolt (Once, I forgot to do up the top suspension bolts tight enough, and it would make clunking noises.

could be bushes.

Could be shocks.

If you work on your own car, then maybe inspect the shocks and look for oil leaks, check seals etc.

If you don't feel confident working on your own car, try a suspensions place.

Also, try listening out for where the noise comes from and what is making it. I know it sounds silly, but different problems make slightly different noises.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...