Jump to content
SAU Community

Recommended Posts

does anyone know the exact reason for ppl to switch over to Z32 afm?

I searched the forum before...found out that they are of the same diameter...and possibly giving different voltage...

the larger afm 90mm dia is from infinity Q45

so why do more ppl choose to upgrade more to Z32 afm in comparison to the infinity afm?

are there any aftermarket afm available? has anyone changed into Z32 or infinity afm in their r34? I know it can be done in r32 and 33s..but haven't actually heard for r34..

thanks

Link to comment
https://www.sau.com.au/forums/topic/97825-z32-afm/
Share on other sites

Its all covered, maybe search a tad harder

Im only going to be brief

Z32/Q45 is used when you max out the stock one, how much air it reads.

Bigger AFM's (Z32/Q45) have a different resolution, giving ability to "see" more air.

Z32 is cheap, $450 delivered. Q45 maybe a bit more

Personally i feel dia of an AFM means squat. Its before the air is compressed, i cant see it as a restirction.

You need Aftermarket Management, PFC etc to use a bigger AFM. Will not work with a stock ECU. Plenty of R34's running around.

There are nismo AFM's also. Basically Z32 in stock size (GTR) so it bolts to stock piping but works as a Z32

cheers

Link to comment
https://www.sau.com.au/forums/topic/97825-z32-afm/#findComment-1777003
Share on other sites

Its a dyno figure, and all those parts (engine) add to more than 8k.

Make it do that day in day out for a few months. Then you'll know that its expensive as you'll have the motor out for rebuild.

Put it this way, settle for 350rwhp and it's achievable well under 8k

Link to comment
https://www.sau.com.au/forums/topic/97825-z32-afm/#findComment-1788788
Share on other sites

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...