Jump to content
SAU Community

Recommended Posts

  • Replies 129
  • Created
  • Last Reply

Top Posters In This Topic

also some more news...

the lebonese girl that got bashed in nulla on sunday has passed away.

and 2 girls in parramatta have been attacked

If she has passed away, then shit is really gonna hit the fan....

Just got this in an email

You have all probably heard about the riots etc in Cronulla, We have

just

been warned as an Insurance Company for Motor Vehicles that the Ethnic

community are ready to retaliate and hit back at the Australian Race in

the

Parramatta Area.  Today there were fights and attacks at Merrylands and

Granville.

Just all be careful and don't go anywhere by yourselves in that area.

They

are jumping out in front of cars to see what race you are then they

start

to hit the vehicle, even while you are inside.  Do not stop for anybody

and

make sure your doors are locked especially at traffic lights.

All Insurance Companies do not cover acts of Terrorism and Racial Acts

resulting in Riots.  So take extra care.  They do however cover radom

acts

of violence by an unknown but you have to cover the excess.

That email sounds like a load of crap that can only come from the media.

http://theage.com.au/news/national/gang-at...4236039329.html

Started in WA as well now....

Not long till it spreads to other states in my opinion. Johnny boy needs to get his troops out of Iraq and bring them down here.

Oh f**k THIS!!!!, this is getting ridiculous.............my safety (and that of my car) is at risk here.....thats it,

ANY MOB COMING NEAR MY CAR WILL BE MOWED DOWN REGARDLESS OF GENDER, AGE, RACE, SEXUAL ORIENTATION, ENTHNIC ORIENTATION WHATEVER.....YOU WILL BE RUN OVER WHILE I MAKE MY ESCAPE......you have been warned.

end rant

yehh my car :)

cant even drive it, man these people all deserve to die !

they should bring out the army and just use full force and then people will stop rioting, with a MP5 pointed at your head you wont be causing trouble then, will ya !!!!

:):):)

im sooo shitty now

the cops dont do shit !

yehh my car :)

cant even drive it, man these people all deserve to die !

they should bring out the army and just use full force and then people will stop rioting, with a MP5 pointed at your head you wont be causing trouble then, will ya !!!!

:)  :)  :)

im sooo shitty now

the cops dont do shit !

cops are out numbered, this is the 1st time im supporting the police having more power

yehh my car :)

cant even drive it, man these people all deserve to die !

they should bring out the army and just use full force and then people will stop rioting, with a MP5 pointed at your head you wont be causing trouble then, will ya !!!!

:)  :)  :)

im sooo shitty now

the cops dont do shit !

Screw the army....

They gotta bring in some real force....

Maybe Chuck Norris?

Chuck_Norris.jpg

Anyone else we can bring along?

Edited by Stel

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
×
×
  • Create New...