Jump to content
SAU Community

Dyno Result Through Chiptorque

bazr33

By bazr33,
in Engines & Forced Induction

 Share

Recommended Posts

bazr33 Mentor

bazr33

Posted
Posted (edited)

Mods as dated today

Power fc

FMIC

AVCR

Hiflow cat 3"

3"exhaust, middle muffler been taken out

Turbosmart type 3 plumb back bov

CES racing split dump

Tuned in october by fist, they did a good job

my AFR's were a bit rich at 10.5 , and timing was abit advanced

they managed 185rwkw

Monday have taken it to chiptorque, rang up that day got it in tuesday

AFR's been changed, need a new o2 sensor and might be up for new spark plugs because of running so rich they have filled up with shit,

car is now running a 201.7rwkw on 12psi

Dyno result will be posted when i pick up the car.

THanks for ppls comments from my last dyno result , if i didnt have any comments i wouldnt of got it tuned again, but glad i did.

Cheers

Barret

post-14294-1134615592.jpg

post-14294-1134615657.jpg

Edited by bazr33
Link to comment
https://www.sau.com.au/forums/topic/98338-dyno-result-through-chiptorque/
Share on other sites
bazr33 Mentor

bazr33

Posted
  • Author
Posted

yeah

i have been to fist before, and they did a good tune with just havin the standard ecu , and just got the manual put in my car

something was wrong cause it was only on 116rwkw and took it to them and they got 170rwkw, clutch was slippin a bit at top end.

but just with the power fc, must of been a bit too difficult for them.

Cause my afr's were rich as and my timing was advanced right to the end pretty much.

I should have fist reimburse me for my spark plugs and o2 sensor which are now needing replacing, but oh well

just glad my car is running fine now, and no more tuning for a while.

bazr33 Mentor

bazr33

Posted
  • Author
Posted

yeah at the moment its ok

when i get a new oxygen sensor and new spark plugs

should even out the power curve abit

just now i put my foot down and its just putting through too much fuel then needed

but i can tell the difference from what it was before hand

THanks

Scooby Veteran

Scooby

Posted
Posted
How are you reading the chart ?

max power is showing 12:1 

From how i'm reading it, it's only showing 14:1 when its just about to boost at the start.

doh! if I get my 'head out' thats how I read it too now.

my bad.

nice tune :)

interested because i want them to tune my stock ecu.

bazr33 Mentor

bazr33

Posted
  • Author
Posted

yeah the fella that does the tuning, seems to know what he's doing .

His name is rob

i think he's into the skylines as he had a rb26, but blew it up trying to race a motorbike .

There is also Greg in Sales, which i know his son, went to skool with him

found that a bit weird.

Anyway they're top ppl.

My car was on the dyno for 2 hours

$ 400

I have been to APC, FIST, and Mercury Motorsport

And im pretty sure to say Chiptorque have impressed me.

Definately will be going back to them for future mods.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...