Jump to content
SAU Community

Recommended Posts

Hi my names Mark,

Just yesterday I had experienced my car having boosting problems. It would rev to 3,500rpm - 4,000rpm and usually you would feel the boost coming on strong. Yesterday it was probably boosting half as much as it should and I am only running the standard 7psi. The boost gauge seemed to be working ok. Although the heat yesterday would have played a part to it as I do not have a front mount cooler.

I waited until later in the nite although it was still a little warm but much cooler than during the day and it still wasn't boosting like it had been previously.

I am lost for ideas, what do you guys think of the problem?

Thanks Mark

Link to comment
https://www.sau.com.au/forums/topic/9847-boost-problems/
Share on other sites

Hmmm I think I am experiencing a similar problem... On recently I have noticed that when I put my foot down and the car starts to boost it used to just lauch so to speak, now I can hear what appears to be extra large sucking sounds for a short period then the power jumps in. I don't know if I am being paranoid or not but my boost guage ( standard in dash ) doesnt really seem to begoing as high either..

Is it possible I have a hole in a hose or popped a pipe off or something simple???

Link to comment
https://www.sau.com.au/forums/topic/9847-boost-problems/#findComment-153412
Share on other sites

The other thing I have noticed also is that my oil gauge used to sit around the 4 mark pretty constantly, now it seems to vary quite often ( under acceleration and such ) between 2 and 6?

I have checked my oil and its not low or anything like that....

Link to comment
https://www.sau.com.au/forums/topic/9847-boost-problems/#findComment-154418
Share on other sites

MrGTST,

It sounds like a boost leak to me, when you in the drive way pull the accelerator cable and listen for unusual noises, should highlight where the leak is occuring.

I think the oil gauge measures viscosity, therefore it should be higher when cold, and lower when hot.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/9847-boost-problems/#findComment-154698
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey, it's me! Though honestly, if I had 20M in my bank account tomorrow, I would not want to be rid of my car all of the sudden - Which makes me think this is money stuff, not "I actually hate car" stuff. I'd probably double down and buy even more trinkets and fun things for it. If this is not you, then sell it cheaper. It will sell at a certain price after all.
    • This is the LCA mount reloctaion kit. Self explanatory in its description. https://au.gktech.com/products/s13-180sx-r32-subframe-anti-squat-reduction-weld-in-kit?_pos=62&_fid=1e812d392&_ss=c These are the alloy subframe bush inserts that I am using. I like them. https://au.gktech.com/products/rear-subframe-slip-in-collars?_pos=29&_fid=1e812d392&_ss=c Alternatively, if you have original and shitty bushes, you might consider outright replacement with poly. https://au.gktech.com/products/polyurethane-rear-subframe-bushes?_pos=28&_fid=1e812d392&_ss=c I would also higly recommend that you look into adjustable RUCAs and tension rods, so you can sort out the camber and bump steer behaviour, especially if the car will be any more than ~15mm lower than stock. I would also highly recommend the GKTech FUCAs, although you really should do some research and learning on the subjetc of R32 FUCAs before making any decisions. All of this will be criticaly difficult to get through a TÜV inspection too, if that happens to be relevant to you. Note that if you do install the relocation kit, you will absolutely have to replace the associated bushes with spherical joints (you can read all about that on the product page) or upgrade the LCAs also.
    • I picked up my block and head last week and have been slowly assembling it since then. Pictures I took earlier this week. The rest of the auxiliaries are on now. I just have my intake manifold runners to tap for my WMI direct port setup before putting it back on. I should hopefully have the motor back in by this weekend.   
×
×
  • Create New...