Jump to content
SAU Community

Recommended Posts

I don't believe they will destroy the coil packs, but if you have standard coils irridium plugs will make them work harder. For the best performance with these plugs you probably need a set of split-fire coils and have your plugs gapped correctly. i.e. high boost smaller gap around 0.8 to 0.9mm. Standard boost then the 1.1 gap will work ok.

I changed to NGK irridiums about 4 months ago and had nothing but trouble, misfiring, hesitation in the mid rev range. The smaller gap solved the misfiring but the car just never reved the way it used to. This is because my standard coil packs couldn't handle the irridium plugs.

I recently changed my irridiums to NGK copper ®, gapped them at 0.9mm and the car runs like a dream. They will only last about 20-30k depending on how you drive, but for $20.00 for a set of 6 who's complaining.

If you feel that you need the better plug, best to stick with NGK platium. The only problem is they come pre-gapped so you need to order them with your preferred gap.

Paul.

umm, okay. So, should I be overly concerned about this? Does damage usually occur within weeks, or do I have a few months?

Its not really damage that occurs, it's just that they don't work as well. Especially if the coil packs are getting older this doesn't help. Eventually of course a coil pack will die. If you stick with irridums then use splitfire coils, around $800.00.

Paul.

in a good way thats good to know..when I bought my skyline almost 3 months ago, my mate made me buy the iridium plugs. Spend a fortune, then figured it was too much hassle to change them, on account of the ornament and piping covering up the plugs and coils..so they've just been sitting there in my garage for the last 3 months...

Hey can someone please explain why you guys are making the spark smaller??? I dont understand, really it doesnt make sence, well not for me anyway.

I thought the bigger the spark the better the bang?

also matty_tonkin Super cheap sell them, $20 for a set of 6

Edited by 7yphon

The deal with closing the gap is that with running higher boost the forced air can blow the spark out.

Which causes the car to go and sound like a heap of crap when it hits full boost.

I bought Iridium 0.8's for my car when it came over because even though running factory boost levels it wouldn't handle it when it hit around 5000rpm.

And plugs that were in it were Iridium 1.1's

but ive heard that compared to japan our premium fuel quality would be there everyday cheap stuff.

Thats what i know anyway, hope it helps. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...