Jump to content
SAU Community

Recommended Posts

Hi all just finish a Drift day here in Darwin but about a week ago I had a new knock in the engine as it starts up but then goes away.

I have had a few people look at it and I am lead to believe that the big end is on it's way out or a gudgen pin on the piston is also on its way out.

either way I feel it is going to be cheaper to get a front cut as I need a few other thing like A/C compressor, steering rack, brake booster.

So if anyone can point me in the right direction pls advise me

[email protected]

0438890852

billy

Link to comment
https://www.sau.com.au/forums/topic/99931-where-to-get-a-cefiro-front-cut-from/
Share on other sites

Hi

Being in Darwin, rebuild not the best way? RB24!

If you are just after an engine, can try Ichiban, around $700 for complete engine, tested. Sydney.

There was a guy in Melbourne that was advertising Cefiro half cuts, but have not seen for a couple of months.

Hope this helps!

2.4 strocker kit would be nice but thinking practical at the monment

I am after the ceffy front cut for the other items brake booster, steering rack, a/c compressor and a few other odds and ends. I suppose that this way i can get it all covered

but I think if nothing just a RB20det engine might be the way to go!!

CeffyNSW; is Ichiban a shop in SYD as this is a great price for a RB20det?? and might just go in thats direction for that price

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...