cheez

there was a similar posting of interest last time. hopefully there will be more than 9 cars. lol

dash pad?

nick is right, 4 sleeps to go to another big gor cruise. I think i may rename it to "Daniel's UNofficial GOR Cruise". lol

straight bolt in mate. r33 gtst and gtr seats u can swap. with the rear, undo the 2 bolts on the floor then from the corners push back on the front of the seat and pull up.

wont be so bad cept for it being schoolies, we'll only demo when there is hot chicks bro... ur more than welcome to come check it out.

cheers guys. and yeh pavs, got a trial rear bar. hopefully arrives either tuesday or wednesday. so thursday is possible.

it was done last time. the SE meet cam and met with the 'main' pre meet, so lol at being scared. might happen again. but on a lighter note, y arent u coming paul? more than likely will be more cars than the OFFICIAL gor cruise. lol

Josh_TyepX: ur fine to join in from lorne onwards. we plan to leave the main meet between 10:30 and 10:45. so we'll be in lorne arond 12:30=12:45 like last tym. guys there are 2 pre meets, please check events section for where they are. 6 DAYS TO GO

hey guys just wondering how to take off the rear bar of a 33gtst series 1? i just bought a new rear bar and wanna do a trial fit. tried searching but no good. cheers daniel

its sold to linedup33 pending payment

im looking at the garrett cartridge replacements from rotor master in campbellfield. they do a similar job to slide but with garrett ball bearing cartridge and a hi flowed exhaust housinhg. olts straight back on coz it uses ur stock turbo

bump. price drop

im running a dual port bov. its handy. has atmo and plumb bak which doesnt cause stalling issues like an atmo coz its returns atleast 50% of the air back into the intake. after a tune it make 190kw. it makes the world look when i change gears. but if i were ui would go the twin pod setup. would cost u about $200 to get this with some quality pods, ie apexi or k&n ($50-$80) each and then adaptor plates about $15-$20 each. that will give u good induction noises and have a flutter to when u change gears ith a dose.

i got 19x8 and 19x9 on my gtst. i run only a 3mm slip on spacer at the front. cant even notice it to be honest. and rear has no spacer. i was under the impression that up to 5mm was allowed as rwc, but obviously not.

its single din or din and a half? where in melb are u located?

Item: Playstation Portable (PSP) Age: 12months old Condition: used but in good condition Price: sold pending payment Location: melb. vic (northern suburbs) Contact: 0422 260 649 Comments: kit includes: PSP console charger Face Plate 32mb card only 1 game unfortunayly, RIDGE RACER pics to come up soon.

yeh count me in guys. by then ill have organised my membership too hope fully.

borrowing ur gtr? geez man, i reckon i should sell mine. lol

it needed more boost to compensate for the lack of spin. the blade started kncking and the shaft started to cease so more boost to creat the same power.

u can, which is what im planning on doing, all u need to do is run a relaay through between the 2 vac lines with an alternating switch. 1 sdie is atmo bov, other is stock.

if it breaks at the front, it gets sucked in through the blades, but a centrifugal force would be greater than the suction force therefore keeping the parts that break, infront of the blade before being sucked into it. therefore again, proving my point, edges break, damage the blade in different places over time and eventually causes enough damage to the blade to kill the cartridge.

i beg to differ, i think the damage to the fin on the outer came first, by not being balanced, the edges hit at high rpm, broke away and caused damage to the centre. the more pieces that broke away the more damage to the centre. therefore: the egg came before the chicken

which is wat i been saying. its not dirt or other crap like people are saying

nothing flew through the blades except chunks of the compressor wheel as it breaks up. check the 2nd pick and see how many small chunks are taken out of the blade. these missing chunks would have caused the damage to the centre of the blades and im pretty sure ull find those pieces in ur cat tony, or in ur rear muffler.

finally some1 who thinks along my lines, out of balance starts to break up, jams the comp wheel, and finally BOOM!!