Jump to content
SAU Community

Recommended Posts

i have 2 sets of wheels, 17 and 18 inch. both have semi/street slicks on them with maybe 70% tread left. they havnt been used for say a year, there are no cracks or bits missing out of the tyres, they seem to be in good nick. they have been sitting around tho in a garage. i was jus wondering if age matters, will it affect how the tyre performs? also wat tyre pressures should be run in them for a/ street use b/ drag strip use c/ track/circuit use (from memory i think they are 255s all round)

thanks.

Link to comment
https://www.sau.com.au/forums/topic/100303-does-age-of-a-tyre-matter/
Share on other sites

i have 2 sets of wheels, 17 and 18 inch. both have semi/street slicks on them with maybe 70% tread left. they havnt been used for say a year, there are no cracks or bits missing out of the tyres, they seem to be in good nick. they have been sitting around tho in a garage. i was jus wondering if age matters, will it affect how the tyre performs? also wat tyre pressures should be run in them for a/ street use b/ drag strip use c/ track/circuit use (from memory i think they are 255s all round)

thanks.

What mostly affects R compounds is the number of heat cycles they get put through. Tread face temps get up around 90 degrees on a circuit & the more times they go throught the heat up - cool down cycle the harder they get. BUT (there is always a but) they wear faster than they harden - so don;t worry too much unless you only do hill climbs.

Street - 32psi.

Drap - less don't know

Track - start at 32 & let them down from there. Aim for mid thirties hot. Best check it to run a pyrometer across the treadface after a run.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...