Jump to content
SAU Community

A/c Belt Misaligned? Need Help To Fix This (pics)

BobyYoo

By BobyYoo,
in General Maintenance

 Share

Recommended Posts

BobyYoo Apprentice

BobyYoo

Posted
Posted

I have noticed that one of my belt is misaligned. As you can see on the pics, the belt has 3 teeths, and one of them is outside.

is that the a/c belt?

Could someone tell me how i can put it back correctly? which part should i loosen up, so i could put the belt properly?

IMG_0720.jpg

IMG_0721.jpg

IMG_0723.jpg

IMG_0734.jpg

blind_elk Grand Master

blind_elk

Posted
Posted

That's the Power Steering pump. Couple of ways to solve the problem.

1. Get a 27 mm socket on the crank pulley. Manually turn the engine over while you press sideways on the belt to guide it back into correct alignment. You will probably need 2 people - 1 down below to turn the crank, the other up top to push on the belt.

2. Loosen off the tensioner of the steering pump. It's on the underside of the pump, so it's often easiest if you remove the IC pipe (the one with, is that the BOV?, in your last pic). You may still need to rotate the pump's pulley, pushing the belt sideways (as in 1 above) to guide the belt back into correct alignment.

Hope that makes sense.

BobyYoo Apprentice

BobyYoo

Posted
  • Author
Posted

thanks for the reply,

i dont know if #1 will work, as the belt is really tight, i dont think we can push the belt on without tearing the belt apart.

as for #2, seem to be a bit more difficult, (yes the silver pipe has the bov on the right) . I will check this out

blind_elk Grand Master

blind_elk

Posted
Posted

For #2, the adjustment mechanism is similar to the one for the alternator. It will be more apparent once you remove the IC pipe. I certainly found it far easier to adjust the belt tensioner this way.

GTS4dood Collaborator

GTS4dood

Posted
Posted

hey bobyYoo,

on a totally unrelated topic i noticed in the pics that u have your BOV welded onto the crossover pipe. i had this done aswell when i first got my BOV. then i got my cooler and had to move it to where the stock one was. There was a massive improvement in the sound. but unless your getting a cooler then you'll need something to block up a bloody big hole.

GTAHH Collaborator

GTAHH

Posted
Posted
Personally I'd just get all your belts replaced. I had the same thing happen. It only costs like $150 in parts and labour if you go to nissan.

What he said. The belt is more than likely ripped up from hanging off like that. If you put it on it could snap or sqeak around

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Neil's R33 Gts-t Build

      By The Bogan · Posted

      It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • perry_r33
      Skyline R33 Sedan Tail Lights S2 - (2 SETS Available) Silver & Grey

      By perry_r33 · Posted

      Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • GTSBoy
      First time Skyline owner

      By GTSBoy · Posted

      Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
×
×
  • Create New...