Jump to content
SAU Community

Recommended Posts

hey dudez

got a problem with my r32 gtst

yesterday at about lunch time, i had driven it for about an hour, just normal driving.

didnt drive it until about 9:30 pm. goto start up and it idles at about 1500rpm

goto drive it, it wont rev above 2500rpm, and when it hits 2500rpm, its like it hits the limiter, or like a fuel cut...but when i put my foot on the clutch it will rev, and the problem seemed to go away and i could drive home

played around with it for 20 mins and it seemed to be ok after i put my foot on the clutch and revved it.

drove home on the freeway and everything was fine until i put my foot down in 5th to overtake someone and it just coughed and spluttered and it was ok then i tried again and it just died in the arse and stopped, but it didnt stall.......

pulled over and revved it again, and everthing was ok, it would drive normally and wouldnt splutter or struggle

it did the problem again as i got off the freeway near my house.

now i have to drive my 31 again...it just isnt the same....

any help would be appreciated

cheers

Link to comment
https://www.sau.com.au/forums/topic/100394-idle-problemshelp/
Share on other sites

hey dudez

got a problem with my r32 gtst

yesterday at about lunch time, i had driven it for about an hour, just normal driving.

didnt drive it until about 9:30 pm. goto start up and it idles at about 1500rpm

goto drive it, it wont rev above 2500rpm, and when it hits 2500rpm, its like it hits the limiter, or like a fuel cut...but when i put my foot on the clutch it will rev, and the problem seemed to go away and i could drive home

played around with it for 20 mins and it seemed to be ok after i put my foot on the clutch and revved it.

drove home on the freeway and everything was fine until i put my foot down in 5th to overtake someone and it just coughed and spluttered and it was ok then i tried again and it just died in the arse and stopped, but it didnt stall.......

pulled over and revved it again, and everthing was ok, it would drive normally and wouldnt splutter or struggle

it did the problem again as i got off the freeway near my house.

now i have to drive my 31 again...it just isnt the same....

any help would be appreciated

cheers

no one can help me???? im desperate to get it working.....

I had sorta problems like that with my GTR when i first got it. Ended up being a f**ked airflow metre. Sounds like yours is going in and out of being f**ked, like mine would, i think its age and heat. Unplug your airflow metre, and rev it, it should hit rev limiter at 2500 cause its in a safe mode. Might not be the problem, but it just sounds like it, also check your o2 sensor, it can cause problems too, just if your airflow metre is out, would be a good idea to check or replace your o2 sensor. Hope this can maybe help

Cheers

ok...pulled the afm out, found only one screw holding the plug in....put three more in.

plugged everything back together, still not revving over 2500rpm

pulled apart again....checked all the cooler pipes etc...couldnt see and split hoses, but couldnt see the pipes that actually go into the cooler..maybe they are split or loose there.....

also found that my rear muffler is totally f*kd....all the internals spat out....could this be the problem also???

i midas well change the exhaust but dont know what size or wateva....3" turbo back with hi-flow cat? how big of a muffler

cheers guys.....

  • 2 weeks later...
ok...pulled the afm out, found only one screw holding the plug in....put three more in.

plugged everything back together, still not revving over 2500rpm

pulled apart again....checked all the cooler pipes etc...couldnt see and split hoses, but couldnt see the pipes that actually go into the cooler..maybe they are split or loose there.....

also found that my rear muffler is totally f*kd....all the internals spat out....could this be the problem also???

i midas well change the exhaust but dont know what size or wateva....3" turbo back with hi-flow cat? how big of a muffler

cheers guys.....

No revs above 2500RPM = bad AFM.

Yeah, if the AFM is stuffed, it will not rev over 2500rpm (cuts fuel).

Plus it will be running limp home maps which are really rich, because it can't detect actual airflow due to the afm not working, so it will run like a bag of shit.

A quick check that will confirm this 100% is running the diagnostic mode to show fault codes on the engine warning light.

Edited by RB30-POWER
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
×
×
  • Create New...