Jump to content
SAU Community

Recommended Posts

hey dudez

got a problem with my r32 gtst

yesterday at about lunch time, i had driven it for about an hour, just normal driving.

didnt drive it until about 9:30 pm. goto start up and it idles at about 1500rpm

goto drive it, it wont rev above 2500rpm, and when it hits 2500rpm, its like it hits the limiter, or like a fuel cut...but when i put my foot on the clutch it will rev, and the problem seemed to go away and i could drive home

played around with it for 20 mins and it seemed to be ok after i put my foot on the clutch and revved it.

drove home on the freeway and everything was fine until i put my foot down in 5th to overtake someone and it just coughed and spluttered and it was ok then i tried again and it just died in the arse and stopped, but it didnt stall.......

pulled over and revved it again, and everthing was ok, it would drive normally and wouldnt splutter or struggle

it did the problem again as i got off the freeway near my house.

now i have to drive my 31 again...it just isnt the same....

any help would be appreciated

cheers

Link to comment
https://www.sau.com.au/forums/topic/100394-idle-problemshelp/
Share on other sites

hey dudez

got a problem with my r32 gtst

yesterday at about lunch time, i had driven it for about an hour, just normal driving.

didnt drive it until about 9:30 pm. goto start up and it idles at about 1500rpm

goto drive it, it wont rev above 2500rpm, and when it hits 2500rpm, its like it hits the limiter, or like a fuel cut...but when i put my foot on the clutch it will rev, and the problem seemed to go away and i could drive home

played around with it for 20 mins and it seemed to be ok after i put my foot on the clutch and revved it.

drove home on the freeway and everything was fine until i put my foot down in 5th to overtake someone and it just coughed and spluttered and it was ok then i tried again and it just died in the arse and stopped, but it didnt stall.......

pulled over and revved it again, and everthing was ok, it would drive normally and wouldnt splutter or struggle

it did the problem again as i got off the freeway near my house.

now i have to drive my 31 again...it just isnt the same....

any help would be appreciated

cheers

no one can help me???? im desperate to get it working.....

I had sorta problems like that with my GTR when i first got it. Ended up being a f**ked airflow metre. Sounds like yours is going in and out of being f**ked, like mine would, i think its age and heat. Unplug your airflow metre, and rev it, it should hit rev limiter at 2500 cause its in a safe mode. Might not be the problem, but it just sounds like it, also check your o2 sensor, it can cause problems too, just if your airflow metre is out, would be a good idea to check or replace your o2 sensor. Hope this can maybe help

Cheers

ok...pulled the afm out, found only one screw holding the plug in....put three more in.

plugged everything back together, still not revving over 2500rpm

pulled apart again....checked all the cooler pipes etc...couldnt see and split hoses, but couldnt see the pipes that actually go into the cooler..maybe they are split or loose there.....

also found that my rear muffler is totally f*kd....all the internals spat out....could this be the problem also???

i midas well change the exhaust but dont know what size or wateva....3" turbo back with hi-flow cat? how big of a muffler

cheers guys.....

  • 2 weeks later...
ok...pulled the afm out, found only one screw holding the plug in....put three more in.

plugged everything back together, still not revving over 2500rpm

pulled apart again....checked all the cooler pipes etc...couldnt see and split hoses, but couldnt see the pipes that actually go into the cooler..maybe they are split or loose there.....

also found that my rear muffler is totally f*kd....all the internals spat out....could this be the problem also???

i midas well change the exhaust but dont know what size or wateva....3" turbo back with hi-flow cat? how big of a muffler

cheers guys.....

No revs above 2500RPM = bad AFM.

Yeah, if the AFM is stuffed, it will not rev over 2500rpm (cuts fuel).

Plus it will be running limp home maps which are really rich, because it can't detect actual airflow due to the afm not working, so it will run like a bag of shit.

A quick check that will confirm this 100% is running the diagnostic mode to show fault codes on the engine warning light.

Edited by RB30-POWER
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Drilled the rubber out on a slow speed and it didn't catch much at all. Probably only half a dozen holes was enough to shred the rubber and it dropped off easily leaving the inner sleeve behind. Will tackle that later
    • I havent bought a manual cover for the dash yet and no cluster change, won't bother me too much, I just need to get that auto box gone, manual in! I miss my manual. 🤪. We started last weekend and managed to get the box out. Planning to start putting it in this weekend and then order a single piece tail. We were super careful to take time and not damage anything. It's my first time working under the car.  With my S15 mainly worked in the bay. This time, it was a headache because of three or four bolts only. They simply didnt want to leave thei homr and the one securing the tailshaft, another above the GB, and the one securing the lipstick was a shit. Mates mate, Davo caught fire 🤣, nearly opened his chest up with a grinder 🤦🏽‍♂️ and both mates nearly had a plate from the box land and slit their head open. Fun times. We all survived. Not the easiest working with limited access on jackstands. As I'm sure we can agree these are the memories which make us love our car. For all three of us, was an awesome weekend and Sunday 3.30am before tools down was a fantastic effort. I need to upload pics, but looks like it needs to be via Url now. We used to be able to just upload pics back in the day. It's been that long! 🤪 Im currently spraying rustoleum under body, not because it's rusted. It's super clean, but just so it's protected for the next 10 years. There was a few surface rust spots. Which pretty much wiped off with a 3M scourer.  Really impressed with how well the previous owner maintained it. Bank account went down so quick! Service, then GB - managed to get a spanking new 34 genuine box from Nissan. All the rest of the conversion parts from Kudos.  Went with a Nismo short shifter. New pedals and Exedy Clutch and FW. Ordered the Prp Rear Main Retainer kit which should arrive Friday and my first engine mod part just like I did with my S15 will be the Tomei Expreme Turbo Outlet. Already on order. It'll likely sleep next to me on a pillow during the coming months. 🥰 Last build was on my JET200GT profile and on SAU and Hardtuned I had documented the build. Planning to try to do that again. Brands feel scarce now. Wish we still had ARC and Apexi parts readily available. Exhaust - need some advice on this. I had an Apexi exhaust on the S15 and loved the tone. My mate had a HKS HP Silent on his 33 and suggested I go with that to avoid drone. I can't remember hearing an RB25DET running that so will likely need to wait for a meet or something to hear it.  Not after big power, just enjoy building it, and drivability with minimal negative attention.
    • Have a chat with Ben at Moore Performance or Jesse at JS Performance.
    • Thanks both. All good advice. Reminds me of drilling through stone wall for drainage pipe 😬 I'll let you know how I get on if I still have use of my hands afterwards 😅
    • Finally got shipping number for the intake and throttle body, shipped by UPS, so "should" be in my hands sometime next week, fingers fracking crossed
×
×
  • Create New...