Jump to content
SAU Community

Recommended Posts

Im changing the power steering pump in my car, my only problem is I can't undo the gold bolt that screws into the pump (holding the valve section?). I need to take it off so I can remove the valve(?) and the section of hosing attached to it from the old pump and reconnect it to my new pump.

thanks,

Link to comment
https://www.sau.com.au/forums/topic/100588-changing-power-steering-pump-help/
Share on other sites

The r32 gtr and gtst use the same pump. Its the suction

pipe, and a bracket for one of the hoses is all that is different between two. They mount and adjust the same too.

Its under the pump from memory, 1 bolt or nut as a lock, then another to put tension on the belt.

I have'nt studied the internals yet, but the pulley size is the same. I need to look inside to see if one flows different than the other. My guess is that they are (flow) the same.

Before you do this check your power steering belts tension and remember this. From memory the book states it should have 9-15mm of deflection at 10kg of pressure? So if you push it down with your finger it should roughly move about 1cm.

I just undid the long bolt at the top which holds the PS pump to the engine bracket. I couldn't take this bolt right out at this stage as the pulley holes werent lined up with it. Then I ended up undoing the whole tensioner assembly (2 bolts on the left and one in the middle). Now you can pull the power steering pump down so it's closer to the engine side creating more slack in the belt so you can now remove the belt from the pulley. Rotate the pulley now (as it can turn freely) if need be to line a hole in the pulley up with the top bolt. Remove this long bolt and now you can remove the power steering pump from it's bracket as it's no longer held in by any bolts. I didn't know a good way to drain the power steering fluid so I just took off the hose at the back of the pump and just let the fluid drain out, this is pretty messy so I put lots of newspaper under the car as I didnt have a jack and I couldnt get a oil pan to fit under my car.

Now for the part I had some trouble (took me 2 days because of this), the gold bolt that attaches the hose at the top of the power steering pump. I found this impossible to get off with a shifter but after purchasing a 15/16" socket the next day I was able to eventually get the c*nt off after a few goes. I'm not sure if they're all this hard to undo but I would suggest using a socket wrench as it worked for me!

So after you undo this bolt (btw mine had a washer attached underneath the hosing) you can remove the hosing that it was holding and begin putting your new power steering pump in!

Mine was already clean but if your new pump is looking a bit gritty it might be best to spray some degreaser on it and then give it a hose down before putting it in.

Make sure you do the belt backup to the same tension.

When you've put all the bolts back on (make sure you remember them all) and adjusted the belt tension correctly you can start filling up the resorvoir with PS Fluid. I used Valvoline Formula F Power Steering Fluid ($10 for 1L at Supercheap), it says it specially designed for Ford Falcons or something which had me worried but my mate said he uses it in his WRX and he hasn't had any problems so I went with it. Yeh so just topped the resorvoir up till it registered full then started the car (with the PS resorvoir cap off) and turned the steering wheel lock to lock (this apparently gets rid of air in the system). The car was making an awful sound that you do not want to hear your car make. I checked the fluid and it was down so I topped it up again (air loss and the fact that the hose lines would be empty I guess). Ran the car again and the awful noise was gone so I think the noise was just the pump running dry.

Took the car for a test drive and it seemed fine and havent had any problems with it yet (touch wood).

This is the first time I've done this and I probably made a few mistakes so dont take what I've written as gospel but it worked for me and might give some people a rough idea of what to do if they dont know.

Good guide, just a couple of things....

everything on a line is metric, the big bolt is either 23 or 24mm not 15/16ths

Undo the bolt while the pump is still bolted in place it should be easier since it will sit still. Be really careful with the bolt it has fluid running though it so it can be weaker than a normal bolt.....no wacking with hammers.....

I just undid the long bolt at the top which holds the PS pump to the engine bracket. I couldn't take this bolt right out at this stage as the pulley holes werent lined up with it.

are you talking about the left gold bolt?

IMG_0738.jpg

Then I ended up undoing the whole tensioner assembly (2 bolts on the left and one in the middle). Now you can pull the power steering pump down so it's closer to the engine side creating more slack in the belt so you can now remove the belt from the pulley.

is the picture below, the 2 bolt you're talking about? and the last picture, is that the bolt for the tensioner?

IMG_0741.jpg

IMG_0742.jpg

Edited by BobyYoo

In my pics (see attachments) the bolt circled in red is the bolt which holds the power steering pump to the engine bracket. You need to remove this bolt.

Circled in yellow are the 3 bolts holding the belt tensioner assembly. Two are on the left and the other is in the middle, directly below the bolt that holds the PS pump to the bracket (circled in red).

Shown in blue is the adjuster at the end of the tensioner assembly. As you can see the previous owner had a nice washer and nut collection going on mine lol. This usually adjusts the tension of the belt but since you are taking the entire assembly off there is no need to adjust it to remove the belt.

So you need to drain fluid (i removed the hose at the back of the pump), remove large bolt holding top hose. Remove pump by taking out 3 tensioner assembly bolts (shown in yellow) and remove long bolt holding ps pump to bracket (shown in red).

Thanks Duncan, sorry guys but I did use a 15/16" socket and it still worked but then again I wasn't concerned about wrecking the bolt as one came with my new pump hehe, try to use the correct metric size.

Also as Duncan mentioned it is probably easier to remove the big bolt (the one that holds the top hose on) with the PS pump still in place.

Make sure when you put the new pump in you put all the bolts, hoses etc back on.

If you have anymore questions just ask.

Good luck.

post-17500-1137568290.jpg

post-17500-1137568370.jpg

i see that your pictures are a bit different from a r32, but is almost similar.

It seem to be easier on a r33, because on the r32, my tensioner bolt is in my last picture, and it is underside of the powersteering which is hard to reach.

I will only replace my belt, so i wont do the whole step, but it is a good write up for someone else

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...