Jump to content
SAU Community

Recommended Posts

Maybe he means less desireable in terms of looks?

Most people don't necessarily buy R33s because they think they look better, you'll find most people like the look of R32s and R34s. But when talking about the GTST/GT-T market, its hard to go past the R33. Unlike the R32, its RB25 equiped, more spacious also its almost as good as an R34 and much cheaper. So the most pracitcal/cost efficient choice becomes the R33, hence their popularity.

Yer spot on... I preferred the look of the 32 and 34 over the 33. But I was happy to settle for a 33 which has more to offer in other areas.

I think you have come one step closer to deciphering the ultimate question of some 32 drivers: "WHY would you buy one of those TAXIS!?" :lol:

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Guest Mashrock

driving a 33 is more about the wank factor that "i drive a skyline"

i used to get the whole "race my skyline its the fastest" when i drove the gti-r..

after about 15m you never herd from them again.

but i guess that would be also generalizing them right?

on the other note. i would just say that there are too many of them out there. and too many people tyring to do the same thing. and also because of these new rules there seems to be a cutdown of younger "hoons" and their ease of getting into a car thats quicker than "billy's" commodore.

Edited by Mashrock

there definatly is a wank factor with most people deciding to buy skylines, but for some it purely is performance. for some its a bit of both. it's the majority spoiling it for the minority. people just wanna look cool driving about, its nothing new the yanks were doing it since the fifties.

still, that dosent just apply to skylines, s13's, 300zx's, supra's, even commodores suffer the posing factor.

posing wouldnt be such a bad thing if it didnt involve the usual challanges, slagging of other peoples cars and the general 'act like a tool' culture that goes with it.

Guest Mashrock
prolly just as many if not more 32's....its not our fault they dont stand out :(

some kind of puke factor??

:P

haha f**k i'm going to stop.

my comment made before was probably not called for. but its the same across the board with every car. there are always going to be dickheads involved..

i.e. look at me.

"Beauty is in the eye of the beholder"

To me that means an R-32 - to others an R-33 - whatever floats your boat.

Just don't slag somebody else for their tastes (sounds utopian doesn't it ;-)

np mate, it was all in fun...im sure even you can appreciate a nice 33...i really dont like 32's, mainly the rear, but when i see 1 that i like i can still say "ooo nice 32..."

:P

lol me either, and i hate the rear of 32s as well.

as a matter of fact, R32s have become a new generation of posing cars coz somehow everyone thinks a R32 goes faster than a R33. and thats y they are so popular nowadays.

back to topic, skylines have created a very bad public impression 'skylines=hoons'. so ppl are trying to stay away from them. eventually ppl will realise how good they are.

imo, commonwhores are more likely to be hoons than skylines...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...