Jump to content
SAU Community

Recommended Posts

Hey hey everyone

I'm just looking for a bit of advice, yesterday the engine in my R32 GTS-t died something shot out the bottom of the engine, a piston or something I don't know. Now because the boyfriend was driving it, he feels really bad and said he will pay for the new engine to get put in now i have the decision of if I want to put the standard engine in or something else!!! And also who am I going to get to put it all in??? If anyone knows someone good on the Gold Coast it would be great if you could give me the name!! I would be willing to go to Brisbane if I have too (though I don't really want to go to Brisbane).

So if anyone can help please do!!! Thanks

Jade. :P

Link to comment
https://www.sau.com.au/forums/topic/100886-jadles-engine-died/
Share on other sites

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

damn :P Did think it wasn't looking too healthy with the amount of blowby when I was checking that AFM problem a couple of months back.. but didn't really want to get u worried.

I think best solution may be an RB25 halfcut and go that route.. may cost $1000-2k more will add to the sellability of the car as well if you guys decide to sell it later on.

A few dudes are always after little bits and pieces for the rb20 which u can sell eventually for $50 here, $100 there, etc (head, turbo, injectors, loom, ecu, etc)

I hear J's Garage is the ducks nuts!

Even to do the wiring and computer if I want to put an rb25 in it!!! (Which I'm considering)?? That would be good if he could do that'

J's garage has access to someone who has just done all of this :P

I had a quote for a half cut of a R33 gtr 1996 to buy and to get installed for $6,000 including engine, turbo, wiring, intercooler, brakes, ummm i'm forgetting something but yeah, what do we think of that???

I don't really want to put the rb20 back in i was going more for the rb25 though I want the right person to install it!! I always get ripped when I take it to get serviced so I know i'll get ripped doing this job!!

Even to do the wiring and computer if I want to put an rb25 in it!!! (Which I'm considering)?? That would be good if he could do that'

I did this conversion myself in June last year and can highly recommend it. With the stock turbo the RB25 offers great low down punch. I wired up a 'Plug 'n' Play' loom to enable the use of the factory ECU. With a PFC and a little more boost you will have a reasonably quick streetcar.

If you do choose the RB25 option though, I would recommend looking for a motor out of an R33 and not the stagea as there appears to be a little more involved in wiring up the loom to run off the stock ECU (I looked at it recently for a guy in Perth).

I am about to wire up a loom for a another member of SAU who is going to put an RB25 in his cefiro and I will be taking pics of the process (I placed some less detailed pics of my loom in my members gallery).

If you would like assistance with any aspect of the conversion feel free to drop me an email or PM. I took plenty of pics of my conversion so I can forward them to you.

Hope this helps.

Ben

Jay, have your man go with you for quotes, especially at some places mentioned, cause as sad as it sounds some places treat women differently.

As for where I go its a little different considering they were my girlfriends mechanics before mine, and I am glad they do cause I hate wanker mechanics!!!!

If you have something bad to say about a company that has been mentioned in this thread, please pm the person with your issues instead of slandering business on a public forum.

Slander - A type of defamation. Slander is an untruthful oral (spoken) statement about a person that harms the person's reputation or standing in the community

Now that we have the correct definition of Slander posted above, I have no issue posting what happened in my case as its true, not an untruthful statement.

I have no doubt in my mine Gavin Wood knows more then his fair share when it comes to GTR’s and tuning how ever his poor customer service lack of interest and knowledge with engine conversion cars and his silly price’s makes one wounder.

He had nothing but issue’s with trying to tune a 600hp RB converted car, charged a silly amount for a SAFC tune that he didn’t do due to a bad senor - You’d think you would charge for pointing out the problem, not charging to tune a car you didn’t and admitted to not tuning eh.

From other peoples comments in person, on this site in the past and on other forums he appears to have no interest in pretty much nothing that’s not a GTR nowadays, yet he calls him self the “Skyline expert”..

Edited by Nismo_Boy
Jay, have your man go with you for quotes, especially at some places mentioned, cause as sad as it sounds some places treat women differently.

As for where I go its a little different considering they were my girlfriends mechanics before mine, and I am glad they do cause I hate wanker mechanics!!!!

Yeah, wanker mechanics are the worst! :)

I think I'm going to go with the RB26 it a half cut of the R33 1996 gtr and bought and installed for $6,000 including after market intercooler, brakes, turbo, wiring, computer (i don’t know if i want to change my computer though) and yeah!!

I'm having a look at it today!!

One of the SAU members mentioned a mech that I'm going to look into too!!!

Thanks for all the tips guys. If there is any more info you can give me that would be great.

Thanks BH_SLO32 I would be shit to do that and there is no way I would let the bf do it, and i don’t think my insurance would like that!!

Who does engineers plates too?? Would they approve this conversion??

There is no need for an engineers plate(afaik) because r32 did come out with an rb25 as well.

but, that being said, i would recommend it anyway, make it look more legit and less likely to be picked on for mods if its been done right, and approved.

as for the rb26conversion.....that is a great engine to throw into a gts-t....untill you break it, then you'll wish you got a 25....they are soooo much cheaper to fix/replace.

6k would get you a weapon 25, or a stock 26...

also with the 25 you can use most if not all the boltons you already have...with the 26 you are starting from scratch.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...